Contact Us

VBL17R15SE

Brand: VBsemi
VBsemi VBL17R15SE is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL17R15SE — Discrete & Power Semiconductors | Superb Automation

VBL17R15SE

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL17R15SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL17R15SE: 700 V and 15 A in a TO263 body

The VBL17R15SE is a single N channel MOSFET in a TO263 body rated at 700 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 15 A of drain current and 260 milliohm at a 10 V gate. The die is listed as SJ deep trench, the charge balance structure with the trench etched deeper than the epitaxy columns of the older process.

Seven hundred volts is the class used on a 480 V AC drive after rectification, where the DC bus sits near 680 V, and on a 600 V DC bus with a small margin. It is the smallest margin class that covers those rails, which is why it exists: a 650 V part on a 680 V bus has no headroom for a regeneration event and a 900 V part costs more resistance for the same die area.

Two hundred and sixty milliohm is high for a part with a 15 A label. At 15 A the loss is 58.5 W, which no TO263 removes. At 5 A the loss is 6.5 W, which a good pad holds. At 3 A the loss is 2.3 W, which is easy. The resistance sets the working current, not the label.

Key data for the VBL17R15SE

ConfigurationSingle N channel
PackageTO263, surface mount with the tab on the drain
VDS700 V
VGSPlus or minus 30 V
Vth3.5 V
ID15 A, a die figure at a 25 C case
RDS(on) at 10 V260 milliohm
TechnologySJ deep trench
Loss at 3 A2.3 W at 260 milliohm
Loss at 5 A6.5 W at 260 milliohm
Loss at 15 A58.5 W at 260 milliohm
Gate chargeNot printed, ask for the curve at the working drain voltage

Why 700 V sits where it does

A 480 V AC line rectified gives about 680 V DC at nominal and higher at the top of the tolerance. A 650 V device is on the wrong side of that number before any transient, and a 900 V device pays for the extra voltage with a wider epitaxy, which means more resistance for the same die area and a larger die for the same resistance.

Seven hundred volts covers 680 V with 20 V of margin, which is thin. That margin has to be protected. A metal oxide varistor at the input, a clamp across the bus and a snubber across the switch are not optional on a rail this close to the rating, because the turn off spike adds to the bus voltage and the sum is what the drain sees.

On a 600 V bus the same part has 100 V of margin and the product is comfortable. That is the common use: a 600 V DC distribution rail, a solar string at 550 V open circuit, a battery string at 600 V. In each case the part is chosen for the voltage and sized down from the resistance.

Deep trench charge balance and the body diode.

The deep trench process puts the field plate deeper into the drift region than the older multiple epitaxy structure, which raises the charge balance and lowers the resistance per unit of breakdown voltage. On a 700 V die the gain is real but it comes with a body diode that has a sharper recovery than a plain planar part.

In a bridge leg the recovery of that diode is the loss that decides the switching frequency. At 20 kHz and 5 A the recovery can add 2 to 4 W in the opposite device, which on a 6.5 W conduction loss is a large addition. Below 20 kHz it is manageable. Above 50 kHz the part wants a parallel silicon carbide diode or a different topology.

The capacitance also matters at these voltages. A charge balance die has a low output capacitance for its voltage, so the energy stored in that capacitance at 680 V is smaller than on a planar part of the same rating, which is what makes a fast transition possible without a large snubber.

Thermal limits in a TO263 at 700 V

The tab is the drain and it sits at 680 V during the off state, which is a board constraint as much as a thermal one. The copper island under the tab has to keep its distance from the gate trace and from any low voltage node, and a slot in the copper is often the cheapest way to hold the creepage without giving up area.

At 5 A the loss is 6.5 W and a pad of three square centimetres with vias into an inner layer holds it. At 8 A the loss is 16.6 W and the part needs airflow. At 10 A it makes 26 W and the package is out of its depth. The honest continuous figure on a normal two layer board is 4 to 6 A.

Where the load is a pulse rather than a continuous current, the thermal capacitance of the tab and the copper carries the first tens of milliseconds and the average loss decides the temperature. A 15 A pulse of 100 microseconds at a one per cent duty cycle is fine. A 15 A continuous load is not, however the pulse is described.

Where the part fits and where it does not

It fits a 600 V bus auxiliary supply, an active clamp in a 480 V converter, a start up circuit on a 680 V rail, a capacitor discharge path and the primary switch of a flyback up to about 40 kHz. It does not fit a continuous 15 A load, a 690 V AC drive without a clamp, or a high frequency bridge leg without an added diode.

For a 680 V rail the questions that decide the part are the clamp voltage the bus actually reaches and the resistance at the gate voltage the driver delivers. Our supplier quality audit page covers what is checked at the source when a part carries a rail this close to its rating.

The sourcing side of this part is covered on the obsolete part cross reference hub. For a 700 V part in a long life product, that page covers the route from an old code to a part that can still be bought.

Questions we get on this code

Does 700 V cover a 480 V AC input? It covers 680 V nominal with 20 V of margin, which is thin. The bus has to be clamped and the switch snubbed, or the margin is gone on the first transient.

Can it run at 100 kHz? With the body diode recovery and the gate charge of a die this size, 100 kHz leaves little room. Below 40 kHz is where this part is comfortable.

Is the 15 A figure usable? No, not continuous. At 58.5 W the package is far outside its thermal limit. Four to six amps on a good pad is the working range.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.