VBL16R34SFD
Product Specifications
VBL16R34SFD
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL16R34SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL16R34SFD: 600 V and 34 A with 80 milliohm in a TO263
The VBL16R34SFD is a single N channel MOSFET in a TO263 body rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 34 A of drain current and 80 milliohm at a 10 V gate. The die is listed as SJ multiple epitaxy, which is the charge balance structure used at this voltage rather than a plain trench.
The 30 V gate window is the widest in this band and it is the first thing to notice. A 600 V part with a plus or minus 30 V gate can be driven at 15 V with a large margin for ringing, and it can take a negative off bias without stress. Parts at plus or minus 20 V force the gate driver to be gentler.
Eighty milliohm at 34 A is not a combination anyone should use as printed. The loss at 34 A is 92 W. The loss at 10 A is 8 W. The loss at 5 A is 2 W. The current column is a die figure at a case temperature this package does not reach on a real board, and the resistance is what the board can work with.
Key data for the VBL16R34SFD
| Configuration | Single N channel |
| Package | TO263, surface mount with the tab on the drain |
| VDS | 600 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 34 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 80 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 5 A | 2 W at 80 milliohm |
| Loss at 10 A | 8 W at 80 milliohm |
| Loss at 34 A | 92 W at 80 milliohm |
| Gate charge | Not printed on the catalogue page, ask for the curve before fixing a frequency |
Where a 600 V MOSFET beats an IGBT
At 600 V the crossover between this kind of part and an IGBT of the same class sits around 20 to 25 A. Below it the MOSFET wins on conduction loss, above it the IGBT wins because its forward drop stops rising in proportion to the current. At 5 A this part makes 2 W where an IGBT at 1.9 V makes 9.5 W, which is not a small difference on a surface mount body.
That is why a 600 V MOSFET is the right choice for a 400 V bus at a few amps: a small auxiliary supply, a bias converter, a relay driver on a high rail, a capacitor discharge path. It is the wrong choice for a 20 A motor drive at 400 V, where the IGBT or a module is cheaper per watt of loss.
Switching behaviour is the other half. A charge balance die at 600 V has a fast body diode and a low output capacitance for its voltage, which is what makes a 50 to 100 kHz converter possible. The price is that the body diode recovery is abrupt, so a bridge leg needs either a short dead time with a fast gate or an external diode in parallel.
Sixty volts of gate window in practice.
The plus or minus 30 V rating means a 15 V drive with 5 V of overshoot is still well inside the window, and a minus 5 V off bias is comfortable. That is worth having on a part that switches 400 V, because the drain node moves fast and the gate loop picks up the displacement current through the drain to gate capacitance.
A 3.5 V threshold is high enough that the part is properly off at zero gate volts, and low enough that a 10 V drive enhances it fully. It is not a logic level part. A 5 V rail drives it into the linear region and the resistance is not published there, so a 5 V gate cannot be used to argue a loss budget.
The gate charge is the number a driver is sized on and the catalogue page does not print it. Ask for the curve at 400 V before fixing a switching frequency. Without it, the driver current and the transition time are guesses, and transition time is where most of the switching loss hides.
Thermal arithmetic in a TO263
The tab is the drain, so the copper under it is at the switching potential. That is fine for a high side or low side switch as long as the copper island is sized for the voltage, but it rules out bolting the tab to a shared chassis without insulation. The thermal path is the tab, the solder, the copper, and then the board.
At 5 A the loss is 2 W and a pad of reasonable size holds it. At 10 A the loss is 8 W and the pad has to be large, with vias into an inner layer if the board has one. At 15 A the loss is 18 W and the part needs airflow or a thicker copper layer. This is the practical ceiling for a TO263 and it is two thirds lower than the printed current.
Spacing matters at 600 V on a surface mount body. The drain tab to gate lead gap is small, and flux residue plus dust over a few years is a leakage path. A conformal coat over the part is the normal answer in a product that sees humidity, and it is cheaper than a field return.
Where the part fits and where it does not
It fits a 400 V bus auxiliary supply, a bias converter, an active clamp, a capacitor discharge switch, a high side disconnect on a 400 V rail at a few amps and the primary switch of a flyback up to about 60 kHz. It does not fit a 20 A continuous load in this body, a 480 V AC front end, or a bridge leg without attention to the body diode recovery.
For a part that replaces an existing 600 V device the questions are the gate window, the resistance at the drive voltage available and the recovery of the body diode. Our how to verify a drop in replacement page sets out the checks made before a candidate is accepted in a position like this.
The sourcing side of this part is covered on the power management cross reference. For a part that has to stand in for an existing 600 V device, that page covers the parameters the comparison turns on.
Questions we get on this code
Is this a logic level part? No. The threshold is 3.5 V, so a 5 V drive leaves almost no overdrive. Use 10 V or more, and 12 V is the usual choice.
How much current can it really carry? At 2 W for 5 A and 8 W for 10 A, the answer depends on the copper. On a two layer board with a large pad, 8 to 10 A continuous is a fair working figure.
Does it include a diode? No, the diode is the body diode inside the die. It is fast but abrupt, so a bridge leg may want a parallel Schottky or a tight dead time.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.