Contact Us

VBL165R02

Brand: VBsemi
VBsemi VBL165R02 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL165R02 — Discrete & Power Semiconductors | Superb Automation

VBL165R02

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL165R02 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL165R02: 650 V and 2 A in a planar die

The VBL165R02 is a single N channel MOSFET in a TO263 body rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 2 A of drain current and 4500 milliohm at a 10 V gate. The technology is listed as planar, which is the process that suits high voltage and low current rather than high voltage and low resistance.

Four and a half ohms at 2 A is 18 W of loss at the printed current, which a TO263 tab passes with a good copper area and not much more. At 0.5 A the loss is 1.12 W and the part is comfortable. The working current for this die is nearer 0.5 to 1 A than 2 A.

Six hundred and fifty volts is the class for a rectified 220 V main with a wide high line tolerance, a 400 V DC bus and an offline converter at low power. It is the standard voltage for a small auxiliary supply inside a larger product, where the current is milliamps and the voltage is the whole story.

Key data for the VBL165R02

ConfigurationSingle N channel
PackageTO263, surface mount, tab soldered to the board
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID2 A, a die figure at a 25 C case
RDS(on) at 10 V4500 milliohm
TechnologyPlanar
Loss at 0.2 A0.18 W at 4500 milliohm
Loss at 1 A4.5 W at 4500 milliohm
Loss at 2 A18 W at 4500 milliohm
Thermal pathTab to copper, no isolated substrate

Why a planar die at this voltage

At 650 V and 2 A the die is small and the voltage is the requirement. A planar process gives a rugged die with a wide safe operating area and a body diode that behaves predictably, at the cost of resistance. A superjunction die at the same voltage would reach a tenth of the resistance and would be far less tolerant of avalanche energy.

For a low power offline supply the trade is usually in favour of the planar part. The current is small, the loss at 0.2 A is 0.18 W, and the ruggedness matters more than the resistance because the leakage spike from a small transformer is proportionally large.

Where the supply has to deliver more than about 20 W the planar die at 4.5 ohm becomes the limiting loss, and the superjunction part in this band at 160 milliohm is the better choice. The two are the same voltage and the same body and the difference is the current.

A two amp part in a body built for thirty

The TO263 body is the same one used for the 20 A and 30 A parts in this family. That means the thermal path is far better than the 2 A die needs, which is useful: the loss at 1 A is 4.5 W and the tab removes it comfortably, where a smaller body would not.

It also means the part is chosen for the voltage and the package, not for the current. A board that needs a 650 V switch in a TO263 for a mechanical or an assembly reason can use this die and run it well inside its thermal limit.

The 3.5 V threshold with a 650 V ceiling means a 10 V gate is the minimum for the published resistance and a 12 V drive is better. A 5 V gate would leave the die barely enhanced and the 4500 milliohm figure would not apply.

A 220 V AC main rectified and smoothed is 310 V, and at a 15 per cent high line it is 356 V. The leakage spike from a small transformer adds 60 to 120 V on top for a few hundred nanoseconds. A 650 V part at the 80 per cent rule works to 520 V, which covers the rail and the spike with 44 V left.

That is the reason 650 V is the standard for an offline flyback at low power and 600 V is marginal for the same job. The 650 V class also covers a 400 V DC bus at the low end, where 500 V does not.

Creepage on the tab matters at this voltage. The tab is at drain potential and the leads are a millimetre apart, so a coated board, a slot under the part or a conformal coat is the usual practice at pollution degree 2. It is not a high power part but it is a high voltage one.

Where the part fits and where it does not

It fits a low power offline flyback, an auxiliary bias supply inside a larger converter, a startup circuit, a high voltage discharge switch at low current and a snubber or clamp element. It does not fit a main switch above about 20 W of throughput, where the 160 milliohm superjunction part in this band is the right choice.

For a bias supply the deciding parameters are the leakage spike and the loss at the actual current, not at the printed 2 A. Our component obsolescence management page covers how a part like this is kept available across a long product life.

The sourcing side of this part is covered on the obsolete part cross reference hub. For a long life part whose family is narrowing, that page covers the route from the old code to a part that can be bought.

Questions we get on this code

Is 4.5 ohm normal for 650 V? For a planar die at 2 A, yes. A superjunction part at the same voltage is ten times lower and much less rugged.

Can it carry 2 A continuously? At 18 W of loss, no. The practical figure is nearer 0.5 to 1 A, where the loss is 1.1 to 4.5 W.

Will it work in a 100 W supply? Badly. The die is a low current part; the 160 milliohm superjunction part in this band is the one for that job.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.