Contact Us

VBL1101N

Brand: VBsemi
VBsemi VBL1101N is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL1101N — Discrete & Power Semiconductors | Superb Automation

VBL1101N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL1101N: 100 V and 100 A in a TO263 body

The VBL1101N is a single N channel MOSFET in a TO263 body, rated at 100 V drain to source, plus or minus 20 V on the gate, a 2.5 V threshold, 100 A of drain current, 23 milliohm at a 4.5 V gate and 10 milliohm at a 10 V gate. The TO263 is the surface mount body most catalogues list as D2PAK, with the tab soldered flat to the board.

One hundred volts is the standard class for a 48 V system. A 48 V pack reaches about 58 V at the top of charge, the derating rule at 80 per cent puts the part at 80 V continuous, and that leaves room for the ringing on a fast node. It is also the class for a 72 V string at the low end and for the primary side of a converter fed from a 60 V bus.

The two resistance columns say this die is usable from a 5 V driver and better from a 10 V one. At 10 milliohm the conduction loss at 30 A is 9 W, which a TO263 with a good copper pad removes. At 4.5 V the same 30 A gives 20.7 W, which no TO263 removes without a heatsink, so the gate drive decides whether the current column is meaningful.

Key data for the VBL1101N

ConfigurationSingle N channel
PackageTO263, surface mount, tab soldered to the board
VDS100 V
VGSPlus or minus 20 V
Vth2.5 V typical
ID100 A, a die figure at a 25 C case
RDS(on) at 4.5 V23 milliohm
RDS(on) at 10 V10 milliohm
TechnologyTrench
Loss at 30 A9 W at 10 milliohm, 20.7 W at 23 milliohm
Loss at 60 A36 W at 10 milliohm
Thermal pathTab to copper, no isolated substrate

The gate voltage decides the whole loss budget

The ratio between the 4.5 V and the 10 V column is 2.3. A loss budget built on the 10 V figure and then built with a 5 V driver is out by a factor of 2.3, and the board that was meant to run at 9 W runs at 20.7 W. That is the single most common way a part like this ends up hotter than the calculation.

Driving the gate at 10 V from a 12 V housekeeping rail is the usual arrangement, with a gate resistor of a few ohms and a diode for a fast turn off. The gate charge is not printed on the catalogue page, so the switching loss has to wait for the curve. For a converter at 100 kHz and 30 A, the switching loss and the conduction loss are of the same order, which makes the curve worth asking for.

The 2.5 V threshold sits between the two columns and is low enough that the part starts conducting well before the gate reaches its final value. On a slow turn on that means a period in the linear region, and the safe operating area of a trench die is not wide. A gate resistor that is too large, or a driver that ramps slowly, turns a hard switched converter into a linear one for a few microseconds.

A hundred amps through a tab ten millimetres wide

A TO263 tab is about 10 mm by 9 mm and it is the only thermal path. At 10 milliohm and 30 A the loss is 9 W, which the tab passes to the copper with a junction to case plus case to board total that a two ounce board with an inner plane can carry. At 60 A the loss is 36 W and the joint becomes the limit long before the die does.

The copper area is the variable that matters. A pad the size of the tab removes a fraction of what a pad three times that size with vias into an inner plane removes. Spreading resistance across the pad adds to the junction to ambient path, so the temperature rise at the edge of the pad is part of the calculation rather than a detail.

At 100 V the tab sits at the drain potential, which on a switching node means the pad is a radiating surface as well as a heatsink. A large pad on a switching node helps thermally and hurts at emissions. The compromise is a pad large enough for the loss with a quiet return underneath and a short connection to the inductor.

Where the part fits and where it does not

It fits the synchronous rectifier of a 48 V to 12 V converter, the low side of a three phase drive on a 48 V pack, a battery disconnect on a 48 V system, the ORing switch on a 48 V bus and the primary switch of a converter fed from a 60 V bus. It does not fit a 96 V pack, and it does not fit a continuous 60 A load on a board without a heavy copper area.

For a 48 V system the parameters that decide the choice are the transient the pack can deliver and the gate voltage the driver actually supplies. Our pin to pin cross reference page covers how a candidate is compared with an original on the parameters that decide behaviour rather than on the headline current.

The sourcing side of this part is covered on the obsolete part cross reference hub. For a 100 V part whose original code is getting hard to buy, that page covers the route from the old code to a part that can be sourced.

Questions we get on this code

Is 100 A usable? Not through a TO263 on a normal board. The figure is a die rating at a 25 C case; the tab, the solder and the copper decide the working number.

Does it work from a 5 V gate driver? It works and the resistance is 23 milliohm, which more than doubles the loss. If the loss budget was built on 10 milliohm, the driver has to change.

Can two of them be paralleled? They can, with a gate resistor each and matched source paths. At 10 milliohm the copper between the two sources is a real part of the total and it decides the sharing.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.