VBK1230N
Product Specifications
VBK1230N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBK1230N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBK1230N: 20 V and 2 A in a SC70-3 body
The VBK1230N is a single N channel MOSFET in a SC70-3 body, rated at 20 V drain to source, plus or minus 20 V on the gate, a threshold window of 0.5 to 1.5 V, 2 A of drain current, 260 milliohm at a 2.5 V gate and 210 milliohm at a 4.5 V gate. The body is the three lead plastic package about two millimetres square.
This is a signal level switch with a power rating on a small pad rather than a power part in a small body. Twenty volts covers a 12 V rail with margin and covers a single lithium cell plus a boost rail. It does not cover a 24 V rail and it does not cover a 12 V automotive rail that sees load dump.
The threshold is printed as a window, 0.5 to 1.5 V, rather than as a typical. That is the honest way to publish a low threshold die, and it is the figure to use when the question is whether the part is off at zero gate volts. At the bottom of the window the part is already conducting at half a volt of gate.
Key data for the VBK1230N
| Configuration | Single N channel |
| Package | SC70-3, three lead surface mount |
| VDS | 20 V |
| VGS | Plus or minus 20 V |
| Vth | 0.5 to 1.5 V window, not a single typical |
| ID | 2 A, a die figure at a 25 C case |
| RDS(on) at 2.5 V | 260 milliohm |
| RDS(on) at 4.5 V | 210 milliohm |
| Technology | Trench |
| Loss at 1 A | 0.21 W at 210 milliohm |
| Loss at 2 A | 0.84 W at 210 milliohm |
| Thermal path | Three small leads, no tab, the board is the heatsink |
What a threshold window means in practice
A window of 0.5 to 1.5 V says the vendor does not guarantee where in that band a given part sits. For a circuit that drives the gate to 2.5 V or more, that does not matter, because both ends of the band are far below the drive. For a circuit that relies on the part being off at 0.3 V of gate, it matters a great deal, because a part at the bottom of the window is partly on.
That is why a part like this belongs behind a driver with a defined low level, or behind a pull down resistor of a few tens of kilohm close to the gate. A floating gate node on a warm board with a low threshold die is a leak path, and in a battery product it is the difference between a shelf life measured in months and one measured in weeks.
The low threshold is also what makes the 2.5 V column meaningful. A 3.3 V logic output, or a 2.5 V rail, can enhance this die fully enough to reach 260 milliohm. A 1.8 V rail cannot, and the resistance there is not published.
Two amps in a three lead package
At 210 milliohm and 2 A the loss is 0.84 W. A SC70-3 body has three leads of about 0.3 mm width and no tab, so the thermal path is the copper under the leads and nothing else. Removing 0.84 W from that is not realistic in still air. The printed 2 A is a die figure at a case temperature this body does not reach on a real board.
At 0.5 A the loss is 0.05 W and the part is easy. At 1 A the loss is 0.21 W and the part is warm but usable with reasonable copper. The practical continuous current for this part on a normal board is nearer 0.5 to 1 A, and the number depends almost entirely on the copper area at the source and drain leads rather than on anything inside the package.
Where a pulse is involved, the thermal mass of the die and the leads carries the first tens of milliseconds and the average loss decides the temperature. A 2 A pulse of a millisecond at a low duty cycle is fine. A 2 A continuous load is not, however the pulse is described.
The land pattern of a three lead body is worth a look before the part is committed. The leads are short and the pads are small, and the copper that spreads the heat is the copper at the source and drain pads. A pad a little larger than the lead on both sides of the drain, plus a via or two into the ground pour, is the difference between a part that runs at 60 C and one that runs at 90 C on the same load.
Where the part fits and where it does not
It fits a load switch on a 5 V or 12 V rail at a few hundred milliamps, a level shift for a higher current device, an LED switch, a small relay driver and a battery disconnect on a single cell product. It does not fit a 24 V rail, a motor winding at an amp continuous, or any place where the loss has to go through three small leads.
For a small load switch the parameters that decide the choice are the threshold window and the copper area at the leads. Our BOM scrubbing page covers how a line of small switches is checked for duplicated codes and mismatched suffixes before an order is placed.
The sourcing side of this part is covered on the date code management. For a small part held between builds, that page covers how the age of a reel is tracked and when it is set aside.
Questions we get on this code
Why is the threshold a range? Because a low threshold die is not trimmed to a single value. The range is what the vendor guarantees, and a circuit that needs a defined off state has to allow for the bottom of it.
Can it switch 2 A? In a pulse, yes. Continuous, expect 0.5 to 1 A depending on copper, because 0.84 W does not leave a three lead body in still air.
Will a 1.8 V logic output drive it? It will turn it partly on. The published resistance starts at 2.5 V, so at 1.8 V the part is conducting but the figure in the table does not apply.
What should a purchase order carry? Part number, SC70-3, and the packing the line can take. We confirm the reel quantity on the offer.