Contact Us

VBI1638

Brand: VBsemi
VBsemi VBI1638 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBI1638 — Discrete & Power Semiconductors | Superb Automation

VBI1638

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBI1638 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBI1638: 60 V and 8 A in the same SOT89 footprint

The VBI1638 is a single N channel MOSFET in a SOT89 body rated at 60 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 8 A of drain current, 40 milliohm at a 4.5 V gate and 30 milliohm at a 10 V gate. Same body and same footprint as the 30 V part in this family, with twice the voltage ceiling.

The resistance columns tell a different story from the 30 V die. This part prints a 4.5 V figure and a 10 V figure, not a 2.5 V figure, so the die is enhanced enough to be usable from a 5 V rail and is specified properly at a 10 V gate. On a 3.3 V rail it still conducts because the threshold is 1.7 V, but the 40 milliohm column does not apply and the real resistance is higher.

60 V is the class used on a 24 V system with transients and on a 36 V or 42 V rail. At the 80 per cent rule it works to 48 V continuously, which covers a 24 V pack at 28.8 V with a wide margin and covers a 36 V pack with less. It does not cover a 48 V lead acid pack at 58 V top of charge, which wants the 80 V or 100 V class.

Key data for the VBI1638

ConfigurationSingle N channel
PackageSOT89, surface mount with a tab on one lead
VDS60 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID8 A, a die figure at a 25 C case
RDS(on) at 4.5 V40 milliohm
RDS(on) at 10 V30 milliohm
TechnologyTrench
Loss at 4 A0.48 W at 30 milliohm
Loss at 8 A1.92 W at 30 milliohm
Gate chargeNot printed, ask for the curve at the working drain voltage

Choosing between the 4.5 V and the 10 V column

The gap between 40 and 30 milliohm is a quarter of the resistance, which is a quarter of the conduction loss. On a 4 A load that is 0.16 W, small but real in a body this size. The reason to care is that a 5 V gate does not reach the 4.5 V column exactly either, because the driver has its own drop and the gate resistor adds a settling time at turn on.

If the rail is 12 V and there is room for a small gate driver, drive the gate at 10 V and use the 30 milliohm figure. If the rail is a 5 V housekeeping supply and the gate comes from a buffer, use the 40 milliohm figure and accept the extra loss. What not to do is quote the 10 V figure in a loss budget while the gate is driven at 5 V, which is the commonest error on a part like this.

The threshold of 1.7 V is low enough that the part turns on from a logic output, and that is the whole point of a low threshold die in a small package. It also means the gate node has to be pulled down hard when the part must be off, since 1.7 V typical leaves less room than a 4 V threshold part for leakage and noise on a high impedance gate node.

60 V on a body this small

A 60 V die in a SOT89 is a compromise between voltage and area. To hold 60 V the epitaxial layer is thicker and the on resistance per unit area is higher than on a 30 V die, which is why the resistance rises from 22 to 30 milliohm for the same body. The compensation is that the part can sit on a 24 V rail without a clamp and on a 36 V rail with a modest one.

Spacing matters at 60 V in a body with leads about a millimetre apart. A coated board or a conformal coat is the usual answer where the part sits near a connector, and the creepage on the tab to the neighbouring lead is worth a look at pollution degree 2. This is not a high voltage part, but 60 V on a fine pitch is enough to track across dust and flux residue over time.

The 1.92 W at 8 A is the figure that decides the real current in this body. A SOT89 with a tab on a generous pad removes a few watts with a good copper area, and about half that on a pad the size of the tab. At 4 A the part is comfortable. At 8 A continuous it is at the edge of what the body can do without airflow.

Where the part fits and where it does not

It fits a load switch on a 24 V rail, the low side of a solenoid or small motor drive, a reverse polarity pass element on a 24 V input, an LED switch and the secondary side of a small flyback. It does not fit a 48 V pack at the top of charge, and it does not fit a position where the body has to remove more than a couple of watts continuously.

For a 24 V input the deciding parameters are the resistance at the gate voltage available and the transient the rail can deliver into the drain. Our how to verify a drop in replacement page sets out the checks made before a candidate is accepted in a position like this.

The sourcing side of this part is covered on the pin to pin cross reference. For a part that has to drop into an existing footprint, that page covers which parameters decide that the swap is safe.

Questions we get on this code

Is this a 5 V gate part or a 10 V gate part? Both, with different resistance. It is specified at 4.5 V and at 10 V, and the loss budget has to use the column that matches the driver.

Can it replace the 30 V part in the same body? Yes on the footprint, and it is the better choice where the rail can rise above 24 V. The cost is 8 milliohm more at the same gate voltage, which at 4 A is 0.13 W.

Does 60 V cover a 48 V system? No. A 48 V pack at 58 V is inside the absolute rating but above the 48 V derated ceiling, and a transient passes both. Use the 100 V class.

What should a purchase order carry? Part number, SOT89, and the packing the line can take. We confirm the reel quantity on the offer.