Contact Us

VBI1322G

Brand: VBsemi
VBsemi VBI1322G is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBI1322G — Discrete & Power Semiconductors | Superb Automation

VBI1322G

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBI1322G from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBI1322G: 30 V and 6.8 A in a SOT89 body

The VBI1322G is a single N channel MOSFET in a SOT89 body, rated at 30 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 6.8 A of drain current, 30 milliohm at a 2.5 V gate and 22 milliohm at a 4.5 V gate. The silicon is a trench die and the package is the small surface mount body with a heatsink tab on one lead.

The two resistance columns are the reason this part is worth a page of its own. Most 30 V parts in a small body publish a single column at 4.5 V and leave the reader to guess what happens on a 3.3 V rail. This one prints a 2.5 V figure and a 4.5 V figure, 30 and 22 milliohm, so a circuit driven from a 2.5 V or 3.3 V logic output knows what it gets. There is no 10 V column, which tells you the die was tuned for a low gate drive rather than for a 12 V rail.

30 V is the class used on a 12 V rail and on the lower end of a 24 V rail. At the 80 per cent derating rule the part works to 24 V continuously, which covers a 12 V system with a wide margin and covers a 24 V system only when the rail is regulated and clamped. A 24 V lead acid pack reaches about 28.8 V at the top of charge and higher during a load dump, so it sits above the derated ceiling of this part and wants the 40 V or 60 V class instead.

Key data for the VBI1322G

ConfigurationSingle N channel
PackageSOT89, surface mount with a tab on one lead
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID6.8 A, a die figure at a 25 C case
RDS(on) at 2.5 V30 milliohm
RDS(on) at 4.5 V22 milliohm
TechnologyTrench
Loss at 3 A0.27 W through the channel at 22 milliohm
Loss at 6.8 A1.39 W through the channel at 22 milliohm
Gate chargeNot printed on the catalogue page, ask for the curve before fixing a frequency

What a 1.7 V threshold buys and what it costs

A 1.7 V typical threshold means the channel is already conducting at a gate voltage a 2.5 V logic output can deliver. That is what makes the 2.5 V column meaningful: the part is usable on the low side of a 3.3 V system where the gate driver is a microcontroller pin and there is no room for a separate 10 V rail.

The cost of a low threshold is leakage and noise margin. At 1.7 V typical the threshold can sit anywhere in a band either side of that figure, and a part at the low end of the band is partly on when the gate is pulled to zero through a weak resistor. In a battery product that sits for months between charges, the pull down has to be strong and the gate node has to be short, or the off state leaks through the channel.

The other cost is Miller turn on. A low threshold die turns on at a lower drain dv/dt through the gate to drain capacitance, so a fast switching node next to it can pull the gate above threshold through the Miller capacitance. Where the part is used as a load switch with a slow ramp this does not matter. Where it sits next to a switching node at 100 kHz or more, the gate needs a hard pull down rather than a soft one.

Thermal reality in a SOT89

The SOT89 body has a tab that is part of the drain lead, and that tab is the whole thermal path. At 22 milliohm the conduction loss at 3 A is 0.27 W, which the body handles on a modest pad. At the printed 6.8 A the loss is 1.39 W, and a SOT89 on a pad of the usual size rises a good deal more than 1.39 W would suggest once the tab sees a still air ambient.

The way out is copper. A pad that extends past the tab, a set of vias into an inner layer and a copper area on the back of the board all lower the thermal resistance, and at these losses the difference between a pad the size of the tab and a pad three times that size is tens of degrees. The number printed in the current column assumes a case temperature a real board rarely holds.

The practical continuous current for this part on a two layer board with one ounce copper is nearer 2 to 3 A than 6.8 A, and the number rises with copper thickness, board area and airflow. If the load is a pulse rather than a continuous current, the thermal capacitance of the tab carries the first part of the pulse and the average loss is what decides the temperature.

Where the part fits and where it does not

It fits the low side of a small motor drive on a 12 V rail, a load switch on a 5 V or 12 V output, the pass element of a linear regulator at low current, an LED string switch and the reverse polarity protection of a small board where a 30 V ceiling is enough. It does not fit an automotive 12 V rail that sees load dump, a 24 V pack at the top of charge, or any place where the drain has to hold more than 24 V in normal operation.

For a switch on a 12 V rail the two figures that decide the choice are the resistance at the gate voltage the driver actually delivers and the loss the body can remove. Our power management cross reference page covers how a candidate is compared with an original on the parameters that decide behaviour rather than on the headline current.

The sourcing side of this part is covered on the one stop BOM sourcing. For a 30 V switch with several small parts around it, that page covers how the group is bought on one order.

Questions we get on this code

Can it be driven from a 3.3 V microcontroller pin? Yes at low current, with a series resistor and a proper pull down. The 2.5 V column says the die is enhanced at that voltage, so 3.3 V is inside its comfort zone. What a pin cannot do is switch the part fast, since the pin sources a few milliamps and the gate charge has to come through the resistor.

Is 6.8 A the current the board can carry? No. It is a die figure at a 25 C case. Work back from 1.39 W at 22 milliohm and from what the tab and the copper can remove, and the working figure lands far below the printed one.

What happens on a 24 V rail? The part works at 24 V until the rail rises. A lead acid pack at the top of charge is 28.8 V, which is inside the 30 V absolute but above the 24 V derated ceiling, and a load dump is above the absolute. Use the 60 V class for that rail.

What should a purchase order carry? Part number, SOT89, and the packing the line can take. We confirm the reel quantity on the offer rather than assuming it.