Contact Us

VBI1101M

Brand: VBsemi
VBsemi VBI1101M is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBI1101M — Discrete & Power Semiconductors | Superb Automation

VBI1101M

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBI1101M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBI1101M: 100 V and 4.2 A in a SOT89

The VBI1101M is a single N channel MOSFET in a SOT89 body, rated at 100 V drain to source, plus or minus 20 V on the gate, a 1.8 V threshold, 4.2 A of drain current, 125 milliohm at a 4.5 V gate and 102 milliohm at 10 V. The silicon is a trench process and the threshold is low enough to call this a logic level part.

A SOT89 is a three legged surface mount body with a tab that is also the drain. It is bigger than a SOT23 and much smaller than a DPAK, and it exists for circuits that need a few amps and a few hundred milliwatts of dissipation without a large pad. The tab gives it a thermal path that a SOT23 does not have.

100 V in this body is not for a power path. It is for a level shift, a startup circuit, a small auxiliary supply, a relay driver with a high voltage rail, and the clamp or the pass element in a control circuit where the voltage is high and the current is small.

Key data for the VBI1101M

ConfigurationSingle N channel
PackageSOT89, three leads and a drain tab
VDS100 V
VGSPlus or minus 20 V
Vth1.8 V typical, a logic level part
ID4.2 A, a die figure
RDS(on) at 4.5 V125 milliohm
RDS(on) at 10 V102 milliohm
TechnologyTrench
Loss at 1 A, 4.5 V gate0.125 W through the channel
Loss at 3 A, 4.5 V gate1.1 W through the channel
Thermal pathDrain tab into the copper, SOT89 has no exposed pad

Reading 125 milliohm at 4.5 V

A 1.8 V threshold means a 3.3 V logic output sits well above threshold and a 5 V output is a full overdrive. The 125 milliohm column at 4.5 V is the one that applies to a 5 V rail, and the 102 milliohm at 10 V is a column that most circuits using this part will never reach. That makes the part honest about its working point: it is a logic level part and its numbers are given at a logic level gate.

At 1 A the loss is 0.125 W, which the tab can pass into a modest copper area. At 3 A it is 1.1 W, and the SOT89 tab, which is about 1.5 mm by 4.5 mm, needs a pad well beyond its own outline. At 4.2 A the loss is over 2 W and the part will run hot regardless of the copper.

The 20 V gate window is comfortable for a 5 V or 12 V rail, and tight for a 24 V rail where the gate is pulled to ground while the source is high. A resistor divider or a zener at the gate is the usual answer in that case.

A further point about the tab: in a SOT89 the tab and the middle lead are the drain, and the drain is the node that moves. That means the tab cannot be tied to a ground plane, so the copper under it is a switching node and it is also a small antenna. Keep the copper under the tab as small as the thermal calculation allows, and run the return current on another layer rather than under the tab, or the loop area and the emissions both grow.

Where a 100 V SOT89 is the right part

It is right where the voltage is high and the current is small: a startup circuit that charges a bootstrap capacitor from a 90 V bus, a level shifter that drives a high side gate in a bridge, a small auxiliary flyback on a 110 V rail, the pass element of a linear post regulator at 50 mA, and a protection clamp that has to hold a spike without failing.

It is wrong where the current is more than an amp or two at high duty. The package heat is then the limit, and a 5 by 6 DFN at the same voltage and a tenth of the resistance is cheaper than a bigger SOT89 with a heatsink.

The third case where it is right is a repair or a small change on an existing board. A SOT89 footprint is often already there, and a part with 100 V and 4 A in that footprint removes the need for a new pad or a new stencil.

Where the part fits and where it does not

It fits a startup circuit on a 90 V bus, a level shifter for a high side gate, an auxiliary supply at a few milliamps, a relay or solenoid driver on a 48 V rail, and a clamp on a control line. It does not fit a power path at 3 A continuous, a 110 V main after rectification where the node can reach 310 V, or a board that needs a low resistance at 5 A.

For a small body at 100 V, the two things that decide whether a substitute is acceptable are the threshold at the gate voltage in use and the copper under the tab. Our how to verify a drop in replacement page sets out the checks made before a substitute is accepted in that position.

The sourcing side of this part is covered on the supplier corrective action. For a part whose behaviour depends on the gate threshold, that page covers how a field return is closed out at the source.

Questions we get on this code

Is it really a logic level part? Yes, with a 1.8 V threshold and a published 4.5 V column. A 3.3 V gate will work at low current, and a 5 V gate uses the printed figure.

Can it carry 4.2 A? For a pulse, with a large pad. Continuous current at 4 A means more than 2 W in a SOT89, which needs a copper area most boards do not give it.

What about the gate at 24 V? Keep the gate to source below 20 V with a divider or a zener. The window is the limit, not the die.

What should a purchase order carry? Part number, SOT89, and the reel quantity. We confirm the packing on the offer.