Contact Us

VBGQT1401

Brand: VBsemi
VBsemi VBGQT1401 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQT1401 — Discrete & Power Semiconductors | Superb Automation

VBGQT1401

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQT1401 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQT1401: 40 V and 1 milliohm in the TOLL body

The VBGQT1401 is a single N channel MOSFET in a TOLL body, rated at 40 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 330 A of drain current and 1 milliohm at a 10 V gate. It is one of the lowest resistance parts in the family and it is built for current paths rather than for high voltage switching.

40 V is the class for a 12 V or 24 V rail, for a 24 V battery with a charging allowance, and for the output of a 48 V to 12 V converter. At 1 milliohm the conduction loss at 100 A is 10 W, which is small enough that the connection to the part becomes the main source of heat, and at 200 A it is 40 W, which is where the copper and the clip decide everything.

A 330 A column in a leadless clip package is a statement about the connection, not only about the die. The die is large, the clips are wide, and the current path from the board to the die is short. That is what makes a part this low usable at all, and it is also what makes the assembly process part of the electrical performance. A void under a clip of this size is a tenth of a milliohm and ten degrees of junction temperature at the same time.

Key data for the VBGQT1401

ConfigurationSingle N channel
PackageTOLL, leadless, clip terminals
VDS40 V
VGSPlus or minus 20 V
Vth3 V typical
ID330 A, a die figure at a 25 C case
RDS(on) at 10 V1 milliohm
TechnologyShielded gate trench
Loss at 50 A2.5 W through the channel
Loss at 150 A22.5 W through the channel
Body diodeIntrinsic, cathode at the drain
Parallel usePossible, but at 1 milliohm the copper between sources sets the sharing

1 milliohm and the rest of the current path

A 1 milliohm part on a board is a small part of a larger resistor. A copper bar 20 mm long and 10 mm wide on two ounce copper is about 0.5 milliohm. A pair of connector contacts is often more than 1 milliohm. A fuse is several. The circuit that loses 2.5 W in the switch at 50 A may lose the same again in the copper on either side of it.

That has a practical consequence for measurement. A four wire reading across the switch terminals at the board includes the copper under the clip and the vias, and it will not match the 1 milliohm on the page. Both the original and the candidate have to be measured at the same points, otherwise a difference in pad geometry is read as a difference in die.

It also has a consequence for the thermal calculation. At 22.5 W the heat is generated in a die a few millimetres across and has to spread into a pad that is much larger. The spreading resistance, not the clip, is the dominant thermal term at that power.

ORing, hot swap and the body diode

In an ORing circuit the body diode conducts before the channel turns on, so the forward drop of the diode is what the load sees during the transition. A 40 V die has a diode with a forward voltage near 0.7 V, and at 50 A that is 35 W for as long as the channel takes to enhance. A fast gate drive keeps that window short, and a slow one turns a routine event into a thermal one.

In a hot swap position the part starts into a discharged capacitance and has to hold the current down while the bank charges. The safe operating area is the deciding curve, not the 330 A column, and a die this large absorbs more energy than a smaller one before the junction leaves its limit.

Where the part is used as a reverse polarity switch, the body diode blocks the wrong way and the channel bypasses the drop in the right way. The gate then has to be referenced to the source on the load side, which is a small circuit of its own and not something the part does by itself.

Where the part fits and where it does not

It fits an ORing switch on a 12 V or 24 V output, a battery disconnect on a 24 V pack, a load switch for a high current rail, the low side of a motor drive on a 24 V battery, and a hot swap switch with an active current limit. It does not fit a 48 V rail without derating, a load dump environment, or a board whose assembly cannot hold a flat leadless part with two large pads.

For a 1 milliohm switch on a current path, the parameters that decide behaviour are the threshold, the resistance at the gate voltage in use and the energy the safe operating area allows. Our power management cross reference page covers how a candidate is compared with an original on the parameters that decide behaviour rather than on the headline current.

The sourcing side of this part is covered on the excess inventory management. For a one milliohm part bought in programme quantities, that page covers how excess is identified and how age is handled.

Questions we get on this code

Can two of them be paralleled? They can, and the copper between the sources is the same order as the die resistance, so the two source paths have to be symmetric. Two gate resistors are needed as well.

Is 330 A a real figure? It is a die rating at a 25 C case. Through the clips on a heavy board it is close for pulses, and the continuous figure is set by the copper and the airflow.

What gate drive does it need? A 10 V rail with a driver that can deliver an amp, and a resistor chosen for the loop rather than for the die.

What should a purchase order carry? Part number, TOLL, and the reel quantity. We confirm the packing on the offer.