Contact Us

VBGP1252N

Brand: VBsemi
VBsemi VBGP1252N is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGP1252N — Discrete & Power Semiconductors | Superb Automation

VBGP1252N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGP1252N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGP1252N: 250 V and 100 A with a screw down tab

The VBGP1252N is a single N channel MOSFET in a TO247 body, rated at 250 V drain to source, plus or minus 20 V on the gate, a 3.5 V threshold, 100 A of drain current and 16 milliohm at a 10 V gate. The silicon is a shielded gate trench and the electrical figures are the same as the 250 V member of this family that comes in a surface mount body, which is the same die in a different package.

That last point is the useful one. When a 250 V die with 16 milliohm exists in both a TO263 and a TO247, the choice between them is entirely thermal and mechanical. The 250 V ceiling on the drain node, the 3.5 V threshold and the 16 milliohm are identical, so a board that has to move from a surface mount body to a screw down tab does not have to re qualify the switching behaviour.

250 V covers a rectified 110 V or 120 V AC rail at 170 V, a 150 V DC bus, and a 96 V battery pack with a wide margin. It is the class for a converter that has to survive a mains borne transient without a large clamp, and for a bridge on a 110 V DC bus where the two switches see the full bus plus the ring.

Key data for the VBGP1252N

ConfigurationSingle N channel
PackageTO247, through hole, tab to a heatsink
VDS250 V
VGSPlus or minus 20 V
Vth3.5 V typical
ID100 A, a die figure at a 25 C case
RDS(on) at 10 V16 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, cathode at the drain
Loss at 25 A10 W through the channel
Derating at 80 per cent200 V continuous working voltage
Gate chargeNot printed, ask for the curve at 170 V drain

Same die, two bodies: when the package changes the answer

A TO263 and a TO247 with the same die behave the same way at the gate and the drain until the case gets hot. The difference is the thermal resistance from the junction to the outside and the current the connection can carry. A TO247 tab is thicker and larger and it is held by a screw, so the path to a heatsink is short and repeatable. A TO263 relies on a solder joint whose voiding decides the temperature.

At 10 W the difference is a few degrees. At 25 W it is the difference between a part that runs at 90 C and one that runs at 130 C, and at 30 W the surface mount joint starts to fatigue over thermal cycles while the screwed tab does not. So the choice is set by the loss the board actually produces, not by the current column.

The other difference is mechanical. A through hole part can be mounted before reflow and it survives the wave. A surface mount part with a large tab needs the reflow profile to be right or the voiding will be visible only in an X ray. Where the assembly line is not set up for a large exposed pad, the through hole body removes a process risk.

The drain spike at 250 V and what it does to the margin

A 200 V working limit and a 250 V ceiling leaves 50 V for the spike. A fast turn off of 25 A with 20 nH of loop inductance produces a di/dt of about 250 A per microsecond and a peak of 5 V per nanohenry, which is 100 V before the capacitance at the node slows it. The clamp and the snubber are what keep the peak under the ceiling, and at this voltage the snubber is not optional.

The second contributor is the reverse recovery of the body diode of the opposite switch in a bridge. When that diode is forced to conduct and then pulled off, the current overshoots and the drain node rings. A 250 V part with a slow diode can produce a worse spike than a 200 V part with a fast one, which is why the diode recovery is worth checking before the voltage margin is accepted.

Where the energy is real and the clamp cannot absorb it, the die avalanche rating becomes the last line. This catalogue page does not print the avalanche energy, so a circuit that relies on it is relying on a figure nobody has stated. Add a clamp or ask for the curve.

Where the part fits and where it does not

It fits the primary switch of a forward converter on a 150 V bus, a half bridge on a 110 V DC bus at 10 to 20 A, a battery disconnect on a 96 V pack, a PFC stage on a 120 V AC input after the rectifier, and any board where a 250 V switch has to be screwed to a heatsink rather than soldered to a pad. It does not fit a 220 V AC input after rectification, a 250 V bus at full derating, or a converter that needs less than 16 milliohm.

For a 250 V switch that has to move from one body to another without a new validation, the electrical match is the easy part and the thermal path is the work. Our vendor consolidation page covers how a line is kept on one qualification across two packages of the same die.

The sourcing side of this part is covered on the how to verify a drop in replacement. For the same die in a different body, that page sets out the checks made before a substitute is accepted.

Questions we get on this code

Is it the same part as the surface mount version? The electrical columns match, which points to one die in two bodies. Confirm the body diode and the gate charge curve before treating them as interchangeable in a bridge.

Can it run without a heatsink? At 5 A the loss is 0.4 W and the tab alone is enough. At 25 A it is 10 W and the part needs a real thermal path.

Does the 250 V rating cover a 220 V AC input? No. A rectified and smoothed 220 V main sits near 310 V, which is above the ceiling before any transient.

What should a purchase order carry? Part number, TO247, and whether the tab is expected to be isolated. We confirm the packing on the offer.