Contact Us

VBGP11505

Brand: VBsemi
VBsemi VBGP11505 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGP11505 — Discrete & Power Semiconductors | Superb Automation

VBGP11505

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGP11505 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGP11505: 150 V and 180 A in the TO247 body

The VBGP11505 is a single N channel MOSFET in a TO247 body, rated at 150 V drain to source, plus or minus 20 V on the gate, a 3.5 V threshold, 180 A of drain current and 4.4 milliohm at a 10 V gate. It is a large die in a large through hole package, and both halves of that sentence matter.

150 V is the class used on 96 V and 110 V batteries, on a 110 V DC bus, and on the high side of a converter fed from a 110 V rail. It is also where a circuit ends up when an 80 V part has too little margin for a load dump but a 200 V part is more silicon than the loss budget allows. The gap between 80 V and 150 V is the most common place in a 48 V to 110 V board to have an argument about margin.

TO247 is the package for a part that has to move a lot of current through a screw down tab. The body is larger than a TO220, the tab is thicker, and the lead spacing is wider, which makes it the usual choice for the main switch of a 3 to 6 kW converter where the thermal path to a heatsink is the deciding factor.

Key data for the VBGP11505

ConfigurationSingle N channel
PackageTO247, through hole, wide lead spacing
VDS150 V
VGSPlus or minus 20 V
Vth3.5 V typical
ID180 A, a die figure at a 25 C case
RDS(on) at 10 V4.4 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, cathode at the drain
Loss at 60 A15.8 W through the channel
Thermal pathTab to a heatsink through a pad or a greased joint
Gate chargeNot printed on the catalogue page, ask for the curve at 100 V drain

Doing the loss sum before choosing the heatsink

At 4.4 milliohm a 60 A load loses 15.8 W in the channel, and that number is what sizes the heatsink. The junction to case resistance of a TO247 is low, around 0.3 to 0.5 C per watt for a large die, so the case runs about 5 to 8 C above the junction. The pad and the heatsink then add 1 to 3 C per watt, and that is where the temperature is really set.

The switching loss sits on top. A 180 A die has a large gate and a large output capacitance, and at 50 kHz with a 110 V bus the crossover loss can be several watts even with a fast driver. For a converter at that frequency the loss split is roughly half conduction and half switching, which means a bigger heatsink does not fix a slow gate drive and a faster gate drive does not fix a small tab.

At 20 A, the same part loses 1.8 W and the heatsink can be a piece of copper on the board. The reason to use a TO247 at that current is not the loss but the margin: a part that runs cold has a long life, and a 4.4 milliohm die at 20 A is barely working.

150 V against 200 V on a 110 V rail

A 110 V bus with a 150 V part leaves 40 V, which is a 73 per cent derating. That is inside the usual 80 per cent rule and it leaves room for the ringing of a fast turn off, but not much for a load dump. Where the rail can see a transient from an inductive load, the 200 V class is the safer pick and the resistance penalty is about a factor of two at the same die area.

The other side of the comparison is the body diode. A 150 V die usually has a faster recovery than a 200 V die of the same process, which matters in a bridge where the diode is forced to conduct during dead time. A slower diode means more loss in the opposite switch and more ringing at the node.

Where the bus is 96 V and the transients are clamped, 150 V is the right class and the 4.4 milliohm die is a large margin in the thermal sense. Where the bus is 110 V and the load is a motor that can regenerate, the 200 V class is worth the extra resistance.

Where the part fits and where it does not

It fits the main switch of a 3 to 6 kW converter on a 96 V or 110 V bus, the low side of a motor drive on a 96 V pack, a battery disconnect on a 110 V string, and a synchronous rectifier on the secondary of a converter whose output is 48 V at high current. It does not fit a rectified 220 V main, a 150 V bus without derating, or a board where a surface mount part is required by the assembly process.

For a 150 V switch that has to be substituted after the original source ends, the parameters that decide behaviour are the threshold, the gate charge at the working drain voltage and the body diode recovery. Our obsolete part cross reference hub page covers the route from an ended code to a part that can be bought and qualified.

The sourcing side of this part is covered on the vendor consolidation. For a high current switch that is bought from more than one source, that page covers which lines stay dual sourced after the consolidation.

Questions we get on this code

Is 180 A usable with a heatsink? The tab and the die can take a large current with a proper heatsink, but the leads and the solder joints are the limit. Most boards run this part at 40 to 80 A continuous and use the current column as headroom for pulses.

Can it be mounted on a live heatsink? The tab is the drain, so a shared heatsink puts the drain on the heatsink. Either isolate the tab with a pad or keep the heatsink isolated and treat it as a live part.

Does the package orientation matter? Yes at these currents. Mount the part so the source lead is short and the gate return runs next to it, otherwise the source inductance steals drive at turn on.

What should a purchase order carry? Part number, TO247, and whether the parts are expected in tubes or in a taped form for the line. We confirm the packing on the offer.