Contact Us

VBFB17R10S

Brand: VBsemi
VBsemi VBFB17R10S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBFB17R10S — Discrete & Power Semiconductors | Superb Automation

VBFB17R10S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBFB17R10S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBFB17R10S: the 700 V, 10 A die in a standing TO251 body

The VBFB17R10S is a single N channel MOSFET in TO251 rated at 700 V, plus or minus 30 V on the gate, 10 A of drain current, with a threshold of 3.5 V and 600 milliohm at a 10 V gate, on superjunction multi epitaxial silicon.

The electrical figures match the TO252 version of the same part number family line for line, which is what you would expect if the same die is used in two packages. That makes the pair useful as a study in what the package alone changes.

At 600 milliohm and 10 A the loss is 60 W, so the part is a 1 to 2 A switch in a real board, and at that current the package difference matters less than the voltage margin.

Key data for the VBFB17R10S

ConfigurationSingle N channel
PackageTO251, IPAK, upright with exposed tab
VDS700 V
VGSPlus or minus 30 V
Vth3.5 V
ID10 A
RDS(on) at 10 V600 milliohm
TechnologySuperjunction, multi epitaxial
Body diodeIntrinsic, hard recovery
Thermal pathTab in free air plus the leads
Gate chargeNot published, modest for the die size
Typical useHigh voltage start up, auxiliary supply, level shift
IsolationNone, the tab is the drain and it is exposed

Same die, different package, different thermal reality

In a TO252 the tab is soldered to a copper pad and the pad is the heatsink. In a TO251 the tab is in the air, so the heat path is the three leads into their pads, which is a far smaller cross section. The junction to ambient resistance roughly doubles.

At 600 milliohm and 1 A the loss is 0.6 W. In a TO252 with a pad that is a 25 C rise, and in a standing TO251 it is nearer 50 C. Both are fine. At 2 A the loss is 2.4 W and the TO251 rise comes close to 120 C, which is where the package starts to decide the current rather than the die.

That is why the same electrical part is chosen in different bodies for different products. A high voltage start up circuit that runs for a second at a time can use the standing body happily. A converter that runs continuously wants the flat body with copper under it.

Where the high voltage part is used at low current

A start up circuit for a flyback carries a few milliamps from the rectified bus into the controller, and the switch holds off the full bus. The loss is a fraction of a watt, the voltage is the only thing that matters, and a 700 V part with 600 milliohm is entirely adequate.

A level shift in a high side driver has the same character: the current is small, the voltage is the bus, and the switching happens at the converter frequency. The gate charge matters more than the resistance because the part spends most of its time switching rather than conducting.

The one place where the resistance matters is a discharge path or a bleeder, where the part is on for a defined time and carries a larger current. There the 600 milliohm turns into watts quickly, and the pulse rating has to come from the data sheet.

The creepage point applies here too, and a standing body makes it easier. The tab is in the air, so the distance from the drain to the board surface is set by the package height rather than by a pad edge, and a slot in the board under the body raises it further. In a 700 V circuit that distance is the difference between a product that passes a hipot test and one that fails it after a humid season. The package does not change the die, but it does change the clearance, and clearance is a safety parameter rather than an electrical one.

A standing body also allows a small clip on heatsink without any board area, which is the practical reason some 700 V products keep using it. A clip rated for the voltage and isolated from the tab adds a few degrees per watt of margin and costs nothing in board space. For a start up circuit that runs continuously in a sealed box, that margin is often what keeps the junction under its limit.

A standing package has one electrical advantage that is easy to miss: the leads are short, so the source inductance is lower than in a flat body with long tabs. In a high voltage switch, source inductance fights the gate drive and slows the turn off, and at 700 V that shows up as a longer overlap and more loss. The difference is small in absolute terms, a few nanohenries, but at 100 kHz it is measurable, and it is the reason some high voltage products keep a standing part even when board area is available.

Where the part fits and where it does not

It fits a 400 to 600 V start up circuit, an auxiliary supply under 10 W, a high voltage level shift, and a bleeder that runs intermittently. It does not fit a continuous converter above 10 W in this body, and it does not fit a rail above 600 V without a clamp.

Our vendor consolidation page covers how one die in two packages is bought from one source, which is usually how a high voltage line is kept to a single qualification.

The sourcing side of this part is covered on the strategic sourcing. For one die bought in two bodies, that page covers how the line is kept on a single qualification across products.

Questions we get on this code

Can the TO251 version replace the TO252 version? Electrically yes if the current is low. Mechanically the footprint is different and the thermal path is worse, so the board has to be rechecked.

What is the gate drive? Ten volts nominal. The 30 V window is for overshoot from a transformer isolated drive, not for a 30 V supply.

Is the tab live? Yes. The tab is the drain and it is exposed, so a heatsink on it has to be isolated or at drain potential.

What should a purchase order carry? Part number, TO251 body, packing type and date code. We confirm the packing on the quotation.