VBE1104N
Product Specifications
VBE1104N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1104N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1104N: a 100 V N channel with a logic level threshold in TO252
The VBE1104N is a single N channel MOSFET in a TO252 body, rated at 100 V drain to source, plus or minus 20 V on the gate, 40 A of drain current, with a threshold of 1.8 V. The catalogue lists 35 milliohm and 30 milliohm in its two resistance columns, on trench silicon.
The threshold is the notable figure. A 100 V die with a 1.8 V threshold is a logic level part at a voltage where most devices are specified at 10 V of gate drive, and that combination is an engineering choice with consequences at both ends of the temperature range.
TO252, also called DPAK, has an exposed tab that is the drain. That tab is the thermal path and it is also an electrical node, which is why the tab has to be isolated from the heatsink or the heatsink has to be at drain potential.
Key data for the VBE1104N
| Configuration | Single N channel |
| Package | TO252, DPAK, exposed drain tab |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V typical |
| ID | 40 A |
| RDS(on) | 35 milliohm and 30 milliohm in the two catalogue columns |
| Technology | Trench |
| Body diode | Intrinsic, forward drop about 0.8 V at rated current |
| Thermal path | Drain tab to the board or to a heatsink |
| Gate charge | Not on the catalogue page, ask before sizing a driver |
| Avalanche rating | Not stated on the catalogue page |
| Typical use | Motor drive, 48 V switching, load control |
What a 1.8 V threshold costs on a 100 V die
To hold 100 V across a trench cell, the drift region under the gate has to be lightly doped and thick, and that region is the main contributor to on resistance. A low threshold means the channel is opened by a thin, heavily doped body region under the gate, which is a separate trade from the drift region.
The consequence is a gate that turns on with a small voltage and a transfer characteristic that is steep near the threshold. At 25 C a 1.8 V threshold part driven from a 3.3 V logic pin has 1.5 V of overdrive. At 125 C the threshold falls by roughly 20 to 30 per cent, so the part turns on earlier, which is normally helpful, and the risk moves to the other end: at minus 40 C the threshold rises, the overdrive shrinks, and a 3.3 V gate may not reach the published resistance.
That is why a logic level part at 100 V is usually driven from 4.5 V or more, even when the data sheet has a 2.5 V column. A driver with a 5 V output, or a 10 V gate derived from a small charge pump, keeps the overdrive comfortable across the whole temperature range.
Forty amps through a DPAK
A TO252 tab is about 30 square millimetres of copper. Soldered to a board with a copper plane, the junction to ambient resistance is somewhere around 40 to 50 degrees per watt. At 30 milliohm and 40 A the conduction loss is 48 W, which is not a number any DPAK survives, so 40 A is a die figure for a pulse or for a case held at 25 C by a heatsink.
Working backwards from a 100 C rise and 45 degrees per watt gives about 2.2 W, which at 30 milliohm is 8.5 A. With a heatsink on the tab and a thermal pad, 15 to 20 A is realistic. The number that matters for a motor drive is the RMS current, not the peak, and the RMS current in a chopper is close to the DC current at full duty.
A last point on how the part is measured. A 35 milliohm figure and a 30 milliohm figure for the same die are usually the 4.5 V and 10 V points, but the difference between them tells you how close the channel is to saturation. Five milliohms of difference is about 15 per cent, which is small for a 100 V die and suggests a gate structure that is nearly fully enhanced at 4.5 V. That is good news for a 5 V driver and bad news for nothing. It does mean the 2.5 V point, if the data sheet prints one, will be well above 40 milliohm, and a 3.3 V drive sits between the two with a resistance no catalogue page states. When a 3.3 V rail is the only gate supply, ask for the resistance curve at that voltage rather than interpolating between two printed points, because the curve is not linear near the threshold.
Where the part fits and where it does not
It fits a 48 V motor drive, a 60 V or 72 V battery load switch, a synchronous rectifier on a 24 V output, and any 100 V rail where the gate drive comes from logic. It does not fit a rail that can ring above 100 V without a snubber, because the catalogue page gives no avalanche rating to lean on.
Our obsolete part cross reference hub page covers what is compared when a 100 V logic level part is being replaced by another body with the same headline numbers but a different drift region.
The sourcing side of this part is covered on the how to verify a drop in replacement. For a 100 V logic level part with a wide threshold window, that page sets out the checks made before a substitute is accepted.
Questions we get on this code
Is 1.8 V the maximum threshold? The catalogue prints a typical. The maximum is normally 0.5 to 0.8 V higher, and that is the number to use when a 3.3 V gate has to guarantee the resistance.
Can two of them be paralleled? Yes, with a separate gate resistor on each and a shared source connection at the tab. Paralleling is limited by threshold matching, so parts from one date code are preferred.
Which resistance column is which? The catalogue prints values in its standard columns without repeating the gate voltage on every row. For a 100 V die the 30 milliohm figure is the 10 V value and 35 milliohm the 4.5 V value. We confirm both from the data sheet before an order is placed.
What should a purchase order carry? Part number, TO252 body, reel size and date code. We confirm the reel size on the quotation.