Contact Us

VBC7P3017

Brand: VBsemi
VBsemi VBC7P3017 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBC7P3017 — Discrete & Power Semiconductors | Superb Automation

VBC7P3017

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBC7P3017 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBC7P3017: a single -30 V P channel at 20 milliohm in TSSOP8

The VBC7P3017 is a single P channel MOSFET in a TSSOP8 body, rated at -30 V, plus or minus 20 V on the gate, -9 A of drain current and a threshold of -1.7 V. The catalogue lists 20 milliohm at a 2.5 V gate and 16 milliohm at 4.5 V, on trench silicon.

The same body that carries two 5 A P channels in the dual version carries one 9 A channel here, and the resistance figure shows it. Twenty milliohm is close to a third of the dual part's 55 milliohm, which means the die is roughly three times the area and the current rating follows the die rather than the package.

What follows from that is a thermal question rather than an electrical one. An eight pin body with no exposed pad moves heat through its leads, and the larger die gives a larger silicon area to spread the heat into a lead frame that did not get bigger.

Key data for the VBC7P3017

ConfigurationSingle P channel
PackageTSSOP8, 0.65 mm pitch
VDS-30 V
VGSPlus or minus 20 V
Vth-1.7 V typical
ID-9 A
RDS(on) at -2.5 V20 milliohm
RDS(on) at -4.5 V16 milliohm
TechnologyTrench
Body diodeIntrinsic, conducts from drain to source above the threshold
Thermal pathLeads only, no thermal pad in this body
Gate chargeNot published on the catalogue page
Typical useHigh side switch on a 5 V or 12 V rail

Nine amps in a leaded body

At 16 milliohm and 9 A the conduction loss is 1.3 W. A TSSOP8 on a normal two layer board with a square centimetre of copper on each lead sits somewhere near 90 to 110 degrees per watt junction to ambient, so 1.3 W is a rise of about 120 to 140 C. From a 50 C ambient that is 170 to 190 C at the junction, which is past any sensible limit.

At 4 A the loss is 256 mW and the rise about 28 C, which is comfortable. At 6 A it is 576 mW and 60 C, which is still workable on a board with decent copper. So the honest continuous current for this part is around 5 to 6 A, and the 9 A figure belongs to a pulse or to a board with a heavy copper plane and forced air.

The lesson is not that the part is overstated. It is that a current rating on a catalogue page is a die limit, and the board decides what the die can actually do. The copper area under the eight leads, the number of vias to an inner plane, and the ambient inside the enclosure are the three numbers that matter, and none of them appear on the catalogue page.

Why a P channel is chosen for a high side switch

A P channel turns on with the gate below the source, so a high side switch on a 5 V or 12 V rail can be driven from a logic output that pulls the gate down, with no charge pump and no bootstrap capacitor. That simplicity is the whole reason P channels still exist in a world where N channels have better figure of merit.

The trade is on resistance. A P channel of the same area has roughly two to three times the resistance of an N channel because the majority carrier is a hole. At 16 milliohm this part is a good P channel, but an N channel of the same body would be nearer 6 milliohm, which is why a 10 A rail is usually switched with an N channel and a charge pump.

The second trade is the gate drive reference. The gate has to be pulled below the source, so the driver sees the source node move when the switch is on. If the source is the load side of the switch, the gate drive has to be referenced to a node that swings, and a resistor from gate to source is needed to hold the switch off when the driver is unpowered.

Where the part fits and where it does not

It fits a 5 V or 12 V high side disconnect, a reverse polarity protection switch on a small board, a battery to load switch where the load is under 5 A, and a power path that has to be simple enough to fit in eight pins. It does not fit a rail that rings above 30 V, and it does not fit a load that draws more than 5 A continuously without a copper plane under the leads.

Our pin to pin cross reference page covers how a substitute is checked pin by pin and parameter by parameter, which is the right method when a TSSOP8 P channel is being replaced by another TSSOP8 part with a different die inside.

The sourcing side of this part is covered on the power management cross reference. For a single P channel being swapped into an existing footprint, that page covers which parameters decide whether the switch still behaves.

Questions we get on this code

Can it be driven from a 3.3 V microcontroller pin? Yes, with the source at 5 V the gate at 0 V gives -5 V, which is past the -4.5 V column. With the source at 12 V the gate at 0 V gives -12 V, still inside the 20 V window.

What happens if the gate is left floating? The switch state is undefined and the body diode still conducts. Put a 100 k resistor from gate to source so the default is off.

Is 20 milliohm measured at 25 C? Catalogue figures are room temperature figures unless stated. Silicon resistance rises with temperature, roughly 0.3 to 0.4 per cent per degree, so at 100 C the 16 milliohm becomes about 21 milliohm.

What should a purchase order carry? Part number, TSSOP8 body, reel size and any date code window the build needs. We confirm what is available on the quotation.