VBBD3222
Product Specifications
VBBD3222
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBBD3222 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBBD3222: two 20 V N channels in a 3 by 2 DFN
The VBBD3222 is a dual N channel MOSFET in a DFN body of 3 by 2 mm with 20 V per device, a plus or minus 20 V gate window, a 1.5 V threshold, a 4.8 A current figure and resistances of 23 milliohm at 4.5 V and 17 milliohm at 10 V.
A 3 by 2 body is the smallest DFN that carries two dies with an exposed pad, and the whole package is a compromise between two pads on one small piece of copper. The pad area available for each die is roughly half of what a 20 V single device would get in the same footprint, so the thermal limit per channel arrives at a lower current.
The part is aimed at portable products: two load switches on adjacent rails, a bidirectional block, two low side legs, or a pair that shares a rail. In those places 4.8 A is a large number and the 23 milliohm is the useful parameter.
Key data for the VBBD3222
| Configuration | Dual N channel, two independent devices |
| Package | DFN 3 by 2 mm, exposed pad, surface mount |
| VDS | 20 V per device |
| VGS | Plus or minus 20 V |
| Vth | 1.5 V |
| ID | 4.8 A |
| RDS(on) at 4.5 V | 23 milliohm |
| RDS(on) at 10 V | 17 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal path | Exposed pad shared by both dies |
| Pin map | Not published on the catalogue page |
| Published applications | DC-DC converter switch, load switch, portable power management |
Two dies on one small pad
At 23 milliohm and 2 A each the loss is 92 mW per channel, 184 mW for the pair, which a 3 by 2 pad on a modest copper landing passes easily. At 4 A each the loss is 368 mW per channel and 736 mW for the pair, which is where the shared pad starts to matter.
The sharing is the important difference from two single packages. Two separate 2 A switches would each have their own pad and their own copper; here one pad serves both, and a hot die raises the other through the common copper. At a few hundred milliwatts the effect is small and at a watt it is not.
The 4.8 A figure is a die limit. The realistic continuous figure for both channels is 2 to 2.5 A each, and for one channel alone about 4 A, which is where the loss is 368 mW and the pad can still pass it.
A 1.5 V threshold and a 20 V gate window
The threshold sits between the low threshold parts and the standard logic level ones. At 4.5 V the overdrive is 3 V, which is ample, and at 2.5 V it is 1 V, which is enough for a load switch and not enough to promise the 23 milliohm.
The 20 V gate window is generous for a 20 V part and makes the gate node tolerant of ringing on a 12 V rail. That combination, a 20 V drain rating with a 20 V gate window, is what allows a part of this size to sit directly on a battery rail without a clamp.
The body diode of each channel is the limitation for a battery path. Two N channels in series with their sources out can block in both directions when off, but a single N channel in a positive rail cannot, and a part used as a reverse polarity block needs the pair.
Coplanarity is the quiet failure mode of a 3 by 2 body. The package is short enough that a small tilt lifts one end of the pad off the paste, and the joint looks closed under a microscope while the thermal path is broken. The inspection that catches it is a cross section on the first build and an X-ray of the pad area on the production lot, plus a check that the placement force is low enough not to squeeze the paste out from under the body before reflow.
Where it fits
It fits two load switches in a handheld product, a bidirectional block in a battery path, two low side legs in a small motor driver, and a synchronous buck in a space constrained module. It does not fit a 20 V rail that rings above the rating, and it does not fit a continuous 4.8 A per channel in still air.
Our NPI production launch checklist page covers what is checked before the first production build, which for a 3 by 2 DFN includes the pad geometry and the paste volume.
The sourcing side of this part is covered on the incoming inspection plan. For a 3 by 2 DFN that has to sit flat on its pad, that page covers what is measured when the reel arrives.
Questions we get on this code
Are the two drains separate? The catalogue describes two independent N channels, and the pin map on the data sheet confirms which pins are which.
Can both channels carry 4.8 A at once? No. The shared pad cannot pass 1.5 W in still air, so 2 to 2.5 A each is the working figure.
Does it work on a 12 V rail? Yes. The 20 V drain rating and 20 V gate window both sit comfortably above a 12 V rail.
What is the difference from a 3 by 3 dual? Board area and thermal headroom. The 3 by 3 pad is 50 per cent larger and takes about 30 per cent more heat.