VBA2207
Product Specifications
VBA2207
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA2207 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA2207: a minus 20 V P channel at minus 15 A in SOP8
The VBA2207 is a single P channel MOSFET in an SOP8 body with a minus 20 V drain to source rating, a plus or minus 20 V gate window, a minus 0.6 V threshold, a drain current of minus 15 A and three resistance columns, 9 milliohm at 2.5 V, 8 milliohm at 4.5 V and 7 milliohm at 10 V.
Three columns across three gate levels with almost no spread is unusual, and here it is the whole story. A P channel whose resistance moves from 9 to 7 milliohm as the gate goes from 2.5 V to 10 V is fully enhanced well before the bottom of that range, which means it can be driven from a 3.3 V rail without a level shifter and without a gate driver.
That is the reason P channels still exist in a world full of N channel parts. A high side switch with a P channel needs one signal and one resistor. The same function with an N channel needs a charge pump, a bootstrap capacitor or an isolated supply, and every one of those is a component that can fail.
Key data for the VBA2207
| Configuration | Single P channel |
| Package | SOP8, surface mount, 1.27 mm pitch |
| VDS | Minus 20 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 0.6 V |
| ID | Minus 15 A |
| RDS(on) at 2.5 V | 9 milliohm |
| RDS(on) at 4.5 V | 8 milliohm |
| RDS(on) at 10 V | 7 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Body diode | Intrinsic, conducts when the drain is above the source by a diode drop |
| Thermal path | Eight leads into the board copper |
A minus 0.6 V threshold is a switching fact, not a detail
A threshold of minus 0.6 V means the channel opens as soon as the gate falls half a volt below the source. For a high side switch on a 12 V rail that is exactly what is wanted: pull the gate to ground and the gate source voltage is minus 12 V, far below the threshold, and the part is hard on. Push the gate to the source with a resistor and the part is off with only leakage between the two.
The same number is a hazard when the gate node is left floating. A minus 0.6 V threshold with a gate that is high impedance during a reset or a brownout can turn the switch partly on, and a partly on P channel in a 12 V path dissipates a few watts without any fault being reported. The resistor from gate to source is not optional in this arrangement, and its value is a compromise between turn off speed and the current it draws from the driving stage.
The plus or minus 20 V gate window is wide for a 20 V part. It allows the gate to sit 20 V below the source, which on a 20 V rail means the gate can be pulled below ground by 20 V without damage. That is generous for transients, and it is the reason the part can be used in a rail where the switch node rings below ground during a load dump.
Fifteen amps through eight leads
At 8 milliohm and 15 A the conduction loss is 1.8 W. As with every SOP8 part, that figure is a die limit, not a working point. On a board with 25 by 25 mm of one ounce copper under the leads, a junction to ambient resistance near 65 degrees per watt gives an 85 C rise at 1.3 W, so the realistic continuous current is around 12 A with a modest copper area and lower if the board is dense.
The comparison that matters is against an N channel plus a charge pump. An N channel at the same current and a quarter of the resistance would dissipate a quarter of the power, but the charge pump adds a switching converter, a capacitor and a diode, and those parts have their own loss and their own failure modes. For currents under about 5 A the P channel wins on simplicity, and above 15 A the N channel wins on heat.
The reverse polarity case is worth separating. When the input is reversed, the body diode of a P channel in the positive lead conducts in the forward direction, and the load sees the diode drop rather than the channel. A part used as a reverse polarity block therefore has to be arranged back to back, or the diode has to be accepted as the conducting path during the fault.
Where it fits
It fits a high side load switch on a 5 V or 12 V rail, a battery disconnect in a portable product, a reverse polarity block in front of a DC input, and a bridge leg driven from a single ended signal. It does not fit a 20 V rail that rings below ground, because the source node is the rail and the drain sees the spike.
Our how to verify a drop in replacement page covers the checks for a P channel swap, and the first two are the threshold window and the gate charge, because two parts with the same resistance can behave completely differently at the edge of the gate rail.
The sourcing side of this part is covered on the power management cross reference. For a P channel that has to keep the same threshold and gate window, that page covers how the comparison is made.
Questions we get on this code
Can the gate be driven from a 3.3 V logic output? Yes for the on state, if the logic output can pull the gate to ground and sink the gate charge. The off state needs a resistor to the source so the gate is not left floating.
Does the part block reverse current when off? No. The body diode conducts from drain to source whatever the gate does, so a true block needs two devices in series.
Is minus 20 V enough for a 12 V rail? With a clamp, yes. A 12 V rail that rings 60 per cent reaches 19 V, and the margin disappears at temperature.
Do you supply the complementary N channel too? We quote what is requested, and we would rather match the pair on threshold and gate charge than on resistance alone.