Contact Us

VBA1328

Brand: VBsemi
VBsemi VBA1328 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1328 — Discrete & Power Semiconductors | Superb Automation

VBA1328

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1328 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1328: a 30 V N channel at 6.8 A with 16 milliohm at a 10 V gate

The VBA1328 is a single N channel MOSFET in an SOP8 body with a 30 V drain to source rating, a plus or minus 20 V gate window, a 1.7 V threshold, a 6.8 A current figure and two resistance columns, 29 milliohm at 4.5 V and 16 milliohm at 10 V, on trench silicon.

This is the ordinary shape of a 30 V logic level part, and the two columns are far apart: 29 against 16 is a factor of 1.8. That gap tells you the die is specified honestly at both gate levels rather than being tuned for one. It also tells you that the gate drive decision changes the loss by nearly a factor of two, which is more than most people expect when they pick a gate resistor.

The 30 V class is the workhorse of 12 V and 24 V systems. A 12 V rail with a transient clamp leaves plenty of margin, a 24 V rail does not, and the difference decides whether this part is comfortable or marginal. That single question, what the rail does on a bad day, is worth more than the resistance column.

Key data for the VBA1328

ConfigurationSingle N channel
PackageSOP8, surface mount, 1.27 mm pitch
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V
ID6.8 A
RDS(on) at 4.5 V29 milliohm
RDS(on) at 10 V16 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeIntrinsic, forward drop sets the loss in a freewheel interval
Thermal pathEight leads into the board copper
Typical partnersGate driver or a 10 V regulator for the gate rail, not a logic pin

The 4.5 V and 10 V columns are two different parts in one body

At 4.5 V the overdrive over a 1.7 V threshold is 2.8 V, and the die sits at 29 milliohm. At 10 V the overdrive is 8.3 V and the die sits at 16 milliohm. The extra 5.5 V of gate drive buys 45 per cent of the resistance, which is the same as buying a die one size larger without changing the footprint.

That is the argument for a dedicated gate rail whenever the board has one. A 12 V system usually has 12 V available, and driving through a resistor from 12 V into a gate rated at 20 V is acceptable if the gate node is clamped. A 5 V system does not, and then the 4.5 V column is the real number and the thermal budget has to be built around 29 milliohm.

There is a second effect that the two columns do not show. A higher gate voltage raises the gate charge that has to be moved every switching cycle, and at some frequency the driver loss overtakes the conduction gain. Without a published gate charge curve the crossover cannot be placed, so a first prototype should measure it rather than assume the 10 V column is always better.

6.8 A and a 30 V rail

At 16 milliohm and 6.8 A the conduction loss is 740 mW. In an SOP8 with no exposed pad and a junction to ambient resistance around 65 degrees per watt, that is a 48 C rise, which is workable at a 60 C ambient and tight at 85 C. At 29 milliohm the same current gives 1.34 W and an 87 C rise, which is no longer workable in a hot enclosure without airflow.

So the two columns do more than change efficiency: one of them changes whether the part can be used at all in a sealed box. That is the reason a 30 V part with a 1.8 to 1 ratio between its columns should be quoted with the gate drive arrangement attached to the quotation, not separately.

Above 12 V input the duty cycle in a buck converter falls, the conduction interval of the switch shortens, and the switching loss becomes the larger term. A part with 16 milliohm and a moderate gate charge can be the better choice at 24 V in and 5 V out than a part with 10 milliohm and twice the charge, because the low resistance is never used.

Where it fits

It fits a 12 V or 24 V synchronous buck at a few amps, a low side switch in a motor drive, a PFC stage in a small adapter, and a load switch on a 12 V distribution rail. It does not fit a 24 V rail that switches an inductive load without a clamp, because the drain sees the supply plus the flyback and 30 V is reached easily.

Our pin to pin cross reference page covers how a candidate is checked against an original, and for an SOP8 single N channel the checks that matter are the pinout, the threshold window and the gate charge rather than the resistance, because two vendors can print the same 16 milliohm on different die sizes.

The sourcing side of this part is covered on the supplier quality audit. For a part whose two gate columns sit far apart, that page covers what an audit checks before a source is used.

Questions we get on this code

Is 30 V enough for a 24 V input? Only with a transient suppressor and a short input loop. A 24 V supply at plus 10 per cent is 26.4 V, and a ringing inductive input reaches the rating with no margin left for temperature.

What gate resistor should the board use? Start at 10 to 22 ohm and measure the switch node. The resistor sets the crossover time and the ringing, and neither can be computed from the catalogue table alone.

Can two of them be paralleled? Yes, with a separate gate resistor on each so the two dies share the current during the crossover. Paralleling without separate resistors lets the faster die take the whole pulse.

What is the reel size? We confirm the size on the quotation rather than stating one here, since SOP8 parts ship on several packings.