VB3102M
Product Specifications
VB3102M
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB3102M from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB3102M: two 100 V N channels in a six lead SOT23
The VB3102M is a dual N channel MOSFET in a SOT23 six lead body, with a 100 V drain to source rating, a plus or minus 20 V gate window, a threshold of 1.5 V, a drain current of 2 A per channel, and an on resistance of 180 milliohm at a 4.5 V gate and 140 milliohm at 10 V.
A hundred volts in a SOT23 is a different job from 30 V in the same body. The die is thicker and the drift region is longer, so the resistance per unit area is far worse, and the package thermal limit is the same as it was. The result is a part that carries amps, not tens of amps, and that is honest about it.
Two channels make it useful in places where a single 100 V switch would need a second part for the return path: a differential pair, a bidirectional block, or two separate rails that share a controller.
Key data for the VB3102M
| Configuration | Dual N channel, independent |
| Package | SOT23, six leads, surface mount |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 1.5 V |
| ID | 2 A per channel |
| RDS(on) at 4.5 V | 180 milliohm |
| RDS(on) at 10 V | 140 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal limit | About 400 to 500 milliwatt in total, both channels share the body |
| Isolation | The two channels share a package, the drain connection has to be read from the data sheet |
Two amps at 140 milliohm is a package figure, not a die figure
At 2 A and 140 milliohm the conduction loss is 560 milliwatt in one channel, which is more than a SOT23 six lead body passes in still air. The rating is therefore set at 25 C case with the leads on copper, and the working current is lower.
A six lead SOT23 with a reasonable pad sits near 200 to 250 degrees per watt junction to ambient without a copper plane, and near 120 with one. At 120 degrees per watt a 100 C rise allows 830 milliwatt, so one channel at 1.5 A and 140 milliohm, 315 milliwatt, is comfortable, and both channels at 1.5 A each is 630 milliwatt, which is at the edge.
That arithmetic sets the practical limit at roughly 1 to 1.5 A per channel continuous, with both channels loaded, in a 60 C ambient. A 100 V part in a small plastic body is a control device, not a power path.
Why a 1.5 V threshold at 100 V is unusual
High voltage dice normally carry a higher threshold, because the gate oxide is thicker to withstand the field. A 1.5 V threshold at 100 V means the vendor built a logic level device with a thin gate oxide and a long drift region, which is a deliberate combination for circuits driven from 5 V logic.
The benefit is that a 5 V gate gives 140 to 180 milliohm without a driver. The risk is the gate oxide. A thin oxide at 100 V drain has to survive the displacement current that flows when the drain swings, and the 20 V window is what protects it. A gate resistor and a short return path are not optional in a circuit that switches 100 V.
There is a second consequence. A low threshold part turns on partly when the gate is left floating and the drain moves, because the Miller capacitance couples the drain edge into the gate. In a bridge this is the mechanism behind spurious turn on, and a pull down resistor of 10 k or less at each gate is the fix.
Where a 100 V dual in SOT23 belongs
It belongs in auxiliary supplies that run from a 48 V or 60 V bus, in Telecom and industrial control where the rail is 48 V nominal, in a bidirectional analog switch on a high voltage signal, and in level shifting between a high voltage domain and logic. It does not belong in a main power path above about 1.5 A, and it does not belong in a circuit that needs a fast switch, because the gate charge of a 100 V die is large against the driver current of a small pin.
Our pin to pin cross reference page sets out the checks for a dual in this body, where the pin map is the first item and the resistance is the third, because a 100 V dual can be pinned with the two drains common or separate and the two versions are not interchangeable.
The sourcing side of this part is covered on the material requirements planning. For a 100 V control part bought in modest quantity, that page covers how a build plan is turned into a purchase plan.
Questions we get on this code
Can the two channels be paralleled for 4 A? Two dice in one body still share one thermal path, so paralleling buys current sharing only if the sources are separate and each has its own resistor. The gain is small and the risk of oscillation is real.
Is it a 100 V part for a 90 V rail? No. A 90 V rail with tolerance and ringing reaches the rating. Use a 150 V class part.
What drive voltage is best? Ten volts gives 140 milliohm and is the efficient choice. Five volts gives 180 and is acceptable where the loss budget allows it.
Is the part available on a small reel? Six lead SOT23 usually ships on 3000 piece reels, with a smaller option for prototypes. We confirm what the offer carries.