VB2658
Product Specifications
VB2658
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB2658 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB2658: a 60 V P channel in a three lead SOT23
The VB2658 is a single P channel MOSFET in a SOT23 body with a minus 60 V drain to source rating, a plus or minus 20 V gate window, a threshold of minus 1.7 V, a drain current of minus 5.2 A, and an on resistance of 52 milliohm at a 4.5 V gate and 50 milliohm at 10 V.
A 60 V P channel is a specific tool. It is what a high side switch needs when the rail is 48 V, when the load is a battery string, or when a reverse polarity block has to survive a 60 V transient without a charge pump. Above 60 V the P channel market thins quickly, so this voltage class is where the practical options stop.
The two resistance columns are the interesting part. Fifty two milliohm at a 4.5 V gate and fifty at 10 V is a 4 per cent change, which is almost nothing, and it says something about how the die was built.
Key data for the VB2658
| Configuration | Single P channel |
| Package | SOT23, three leads, surface mount |
| VDS | Minus 60 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 1.7 V |
| ID | Minus 5.2 A |
| RDS(on) at 4.5 V | 52 milliohm |
| RDS(on) at 10 V | 50 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal limit | About 350 to 400 milliwatt in still air on a normal pad |
| Body diode | Intrinsic, conducts from drain to source when the drain is above the source |
A 4 per cent difference between two gate voltages needs explaining
On most logic level dice the resistance falls by 20 to 40 per cent between a 4.5 V and a 10 V gate. Here it falls by 4. Three explanations are possible and they are not equivalent.
The first is that the die is fully enhanced by 4.5 V, which happens when the threshold is low relative to the drive and the channel is short. With a minus 1.7 V threshold and a minus 4.5 V gate the overdrive is 2.8 V, which is enough for a low voltage die and plausible for this one. The second is that the 52 figure was measured at 10 V and copied into both columns, which would make the 4.5 V column optimistic. The third is that the 4.5 V measurement was made at a low current where the resistance is dominated by the channel and not by the drift region, so the two columns are not measuring the same thing.
The consequence for a buyer is simple. A circuit that drives the gate at 4.5 V and needs 52 milliohm should confirm the number on the output characteristic. If the true figure at 4.5 V is 60 or 65 milliohm, a 2 A load dissipates 240 to 260 milliwatt rather than 208, which is the difference between a warm SOT23 and a hot one.
Sixty volts on a 48 V rail, and where the margin goes
A 48 V rail with a 10 per cent tolerance reaches 52.8 V, which leaves 7 V of headroom to the rating. A hot plug event on a 48 V bus can produce a spike well above that, and a P channel in the return path of a hot swap circuit sees the full input plus the cable reflection.
The standard answer is a transient suppressor across the input and a gate network that turns the part on slowly, so the inrush is limited by the channel resistance rather than by the wiring. A slow turn on is built with a capacitor from gate to source and a resistor to ground: the capacitor holds the gate near the source while the resistor charges it, and the turn on time is the resistor capacitor product against the gate charge.
At 60 V the safe operating area matters more than at 20 V. A linear mode event, where the part is partly on while the output capacitor charges, puts both high voltage and high current on the die at once, and a SOT23 die has little thermal mass. The inrush energy has to be checked against the curve, not assumed.
Using the body diode deliberately
In a reverse polarity block the P channel is wired with the source to the load and the drain to the input, so the body diode conducts when the input is correct and the channel shorts it out when the gate is driven. That is the standard arrangement and it works because the diode drop is only present until the channel turns on.
The failure case is a reversed input, where the diode blocks and the gate, held at the same potential as the input through a resistor, keeps the channel off. The resistor has to be sized against the leakage of the gate and the voltage of the reverse case, because a resistor too large lets the gate drift and a resistor too small wastes current in normal operation.
Our OEM procurement page covers how a part like this is bought against a programme rather than against a single order, which matters because a 60 V P channel in SOT23 has a small number of sources and a long lead time when the market tightens.
The sourcing side of this part is covered on the component obsolescence management. For a 60 V P channel with a thin second source, that page covers how end of life is tracked before it becomes an emergency.
Questions we get on this code
Can it be driven from a 5 V logic output? Yes for a 12 V or 24 V rail, through a small N channel that pulls the gate down. For a 48 V rail the gate has to be pulled 10 V below the source, and a 5 V logic pin cannot do that on its own.
How much current can it really pass? About 1.5 to 2 A continuous on a normal pad, because the loss at 2 A and 52 milliohm is 208 milliwatt against a body limit near 400.
Is 60 V enough for a 48 V battery string? Only with a suppressor. A charged string plus a charger overshoot can pass 60 V, and the rating is a limit, not a working point.
What is the reel size? SOT23 normally ships on 3000 piece reels. We confirm the size on the offer rather than assuming it.