VB1240B
Product Specifications
VB1240B
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB1240B from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB1240B: the same 20 V body with a wider gate and a better die
The VB1240B is a single N channel MOSFET in a SOT23 three lead body with a 20 V drain to source rating, a plus or minus 20 V gate window, a threshold between 0.5 and 1.5 V, a drain current of 6 A, and an on resistance of 25 milliohm at a 2.5 V gate and 20 milliohm at 4.5 V.
Put beside the VB1240 it is the same body size, the same voltage class and the same current claim, with two differences that matter. The gate window is 20 V rather than 12 V, and the resistance at 4.5 V is 20 milliohm rather than 28. One of those is a die change and one is a screening change, and a buyer should know which is which.
For a board that already uses the earlier part, the B is the better device in both columns. For a new circuit, the B removes the gate clamp that the narrower window needed, which is a part and two joints saved on every channel.
Key data for the VB1240B
| Configuration | Single N channel |
| Package | SOT23, three leads, surface mount |
| VDS | 20 V |
| VGS | Plus or minus 20 V |
| Vth | 0.5 to 1.5 V |
| ID | 6 A |
| RDS(on) at 2.5 V | 25 milliohm |
| RDS(on) at 4.5 V | 20 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal limit | About 350 to 400 milliwatt in still air on a normal pad |
| Comparison with VB1240 | 3 milliohm better at 2.5 V, 8 milliohm better at 4.5 V, 8 V wider gate window |
Twenty eight to twenty milliohm is a die change, not a screening step
A 29 per cent reduction in on resistance at the same voltage class and the same body size is a different die. Screening cannot move a resistance that far, and a package change is ruled out because the body is identical. So the two parts come from different silicon, and the practical question is whether the rest of the characteristics moved with the resistance.
Two parameters usually move when a die is optimised for resistance: the gate charge rises, because more channel area means more capacitance, and the safe operating area narrows, because the cell density that lowers resistance also lowers the thermal mass per unit area. Neither is on the catalogue page, so a circuit that depends on switching speed or on surviving a fault has to ask for both.
For a load switch at low frequency neither matters. For a 200 kHz converter with a 5 V gate drive the gate charge is the switching loss, and a part that is 8 milliohm better and 4 nanocoulombs heavier can be worse overall. That is the calculation to run before treating the B as a free upgrade.
The 20 V gate window in a 12 V system
With 20 V of window, a gate tied through a resistor to a 12 V rail sits at 60 per cent of the rating, which is comfortable and leaves room for a transient. That is the main practical gain over the earlier part: a high side switch in a 12 V circuit no longer needs a zener at the gate.
The window also allows the part to be used as a source follower, where the gate sits above the source by a fixed amount and the source potential moves. In that arrangement the gate to source voltage is what the window protects, and a 20 V window gives enough range for a 12 V rail with the gate pulled to 15 or 16 V.
The 0.5 to 1.5 V threshold is still wide. At a 2.5 V drive the overdrive is between 1.0 and 2.0 V across the spread, so the 25 milliohm column is a typical die figure and the worst die is worse. A circuit that needs consistency should drive at 4.5 V, where the overdrive is 3 V or more on every part.
What the SOT23 still cannot do
Twenty milliohm at 6 A is 720 milliwatt. The body passes about 400 milliwatt in still air. So the better die does not lift the current rating in a real enclosure: it lowers the loss at the same current, which is a different benefit. At 2 A the loss falls from 112 to 80 milliwatt, and at 3 A from 252 to 180, which is the difference between a warm part and a comfortable one.
The lead resistance also caps what the package can claim. A SOT23 lead frame adds a few milliohm in series with the die, and that contribution is included in the catalogue figure at the measurement current but grows with current squared in the loss sum. A board at 4 A sees the body heat up faster than the 20 milliohm alone predicts.
Our power management cross reference page sets out the check sequence for this class of part, and the first item is always the gate window, because a 12 V part in a 20 V socket is a board that works on the bench and fails on a transient.
The sourcing side of this part is covered on the how to verify a drop in replacement. For a part that is often swapped inside one body size, that page sets out the checks before a substitute is accepted.
Questions we get on this code
Is the B a drop in for the plain part? Electrically better and pin compatible, so yes, provided the higher gate charge does not upset a fast switching node. On a slow load switch it is a straight improvement.
Does it need a gate resistor? Yes, 10 to 47 ohm. At this die size the gate capacitance is small and the trace inductance can ring, which is what the resistor damps.
What is the current for a real enclosure? Two to three amps continuous on a normal pad in a 40 to 60 C ambient. Above that the copper area has to grow or the part has to change body.
Is there a 30 V version in the same body? Ask with the voltage and current you need. The catalogue band around this code runs to 60 V in SOT23, so the answer depends on the resistance you can accept.