HXNM40015
Product Specifications
HXNM40015
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXNM40015 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXNM40015: twenty five watts pulsed on 9.3 to 9.5 GHz
The HXNM40015 is a gallium nitride internally matched power amplifier module for the 9.3 to 9.5 GHz window. Hisiwell builds it with in-plane matching synthesis and thin film hybrid integration and specifies 50 ohm at both ports. The index row reads 9.3 to 9.5 GHz, saturation output at least 44 dBm, gain at least 20 dB, drain efficiency at least 35 per cent, 28 V drain rail, mode printed as pulse, flatness not printed.
44 dBm is 25.12 W, and the band is 200 MHz wide. That is 2.13 per cent fractional at a 9.4 GHz centre, which is a channel plan rather than a band. A part matched this tightly is built for one allocation, and the allocation at 9.3 to 9.5 GHz is X band radar. Weather radar, airborne mapping radar and ground surveillance radar all sit in or near this window, and the pulse mode entry in the index row is consistent with that use.
The mode column says pulse and prints no width and no duty cycle. That is the single most important gap in the published data. A 44 dBm part at 35 per cent efficiency dissipates 46.65 W while the pulse is on, and the average dissipation is that figure multiplied by the duty cycle. At 10 per cent duty the average heat is 4.67 W and a modest carrier is enough. At 30 per cent duty it is 14 W and the carrier becomes the limiting item. Without a published duty figure, the safe reading is that the rating belongs to a short pulse and a low duty, and that any continuous operation has to be established by measurement.
The drive requirement is 24 dBm, which is 251 mW. That is a normal driver level for a 25 W X band stage, and it means a two stage line with 44 dB of total gain, which is enough to take a 20 dBm exciter to full output with 24 dB in hand for level control and cable loss.
The parameter rows Hisiwell publishes for HXNM40015
| Part class | Gallium nitride internally matched power amplifier module |
| Matching technique, as stated by the vendor | In-plane matching synthesis, thin film hybrid integration |
| Frequency range | 9.3 to 9.5 GHz |
| Bandwidth, calculated | 200 MHz, 2.13 per cent fractional at a 9.4 GHz centre |
| Saturation output power as published | at least 44 dBm |
| Saturation output power in watts, calculated | 25.12 W |
| Output at 1 dB compression as published | not published, the index prints a slash in that column |
| Gain as published | at least 20 dB |
| Drain efficiency as published | at least 35 per cent |
| Drain voltage | 28 V |
| Input and output impedance | 50 ohm, matched |
| Flatness across the band | not published, the index prints a slash |
| Operating mode | pulse, width and duty cycle not published |
| Drive power for the rated output, calculated | 24 dBm, 251 mW |
| DC input during the pulse, calculated | 71.77 W |
| Drain current during the pulse, calculated | 2.56 A at 28 V |
| Dissipation during the pulse, calculated | 46.65 W |
| Average dissipation at 10 per cent duty, calculated | 4.67 W |
| Average dissipation at 30 per cent duty, calculated | 14.00 W |
| Output per 100 MHz of the band, calculated | 12.56 W |
| Load voltage at saturation into 50 ohm, calculated | 35.44 V RMS, 50.12 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Gate bias point and quiescent current | not published |
| Operating and storage temperature | not published |
| Orderable addendum, marking and packing | not published |
| Neighbour on the same rail at 42 dBm across 8 to 12 GHz | HXNM40012, 20 dB gain |
Reading a pulsed rating without a duty cycle
A pulsed transistor rating without a pulse width or a duty cycle is incomplete in a way that matters. The same part can be a 25 W device that runs cool at one per cent duty and a device that destroys its own flange at fifty per cent duty, and the vendor row prints the same five numbers in both cases. The only defensible route is to take the saturation dissipation, multiply by the duty the system will actually use, and then check the carrier against that average.
For a radar with a one microsecond pulse and a one kilohertz repetition rate, the duty is 0.1 per cent and the average heat is 47 mW. For a radar with a 100 microsecond pulse at 10 per cent duty the average heat is 4.67 W. Both are easy for a metal carrier and neither is a problem. For a continuous wave test on the bench, the part is being run at 100 per cent duty, which is the case the rating does not cover, and a bench test that holds full output for minutes at a time is the fastest way to lose a sample.
The bench plan should therefore mirror the application. Drive the module with the production pulse, measure the flange temperature over ten minutes, and record both the pulse width and the duty in the test record. That record is also what a customer audit will ask for, since it is the only evidence that the part has been run inside its intended mode.
The 200 MHz window makes the pulse spectrum easier to manage than a wideband part would. A one microsecond pulse has a spectral width of about one megahertz, which sits comfortably inside the matched band, and the waveform envelope is not shaped by the matching network. Wideband radar codes with tens of megahertz of bandwidth also fit, and the limit is the 200 MHz window rather than the pulse shape.
Load, harmonics and the 50 ohm reference
At 25.12 W into 50 ohm the load voltage is 35.44 V RMS and 50.12 V peak, above the 28 V rail and close to the flashover point of a small coaxial connector. Every connector, cable and circulator between the module and the antenna has to be rated for 50 V peak at 9.4 GHz with margin for altitude and for a mismatch. A 2:1 mismatch reflects a quarter of the power and raises the peak voltage by a further factor, which is why an isolator or a circulator at the output is normal practice on a radar transmitter.
The second harmonic of 9.4 GHz is 18.8 GHz, well outside the matched band, and no harmonic figure is published. A radar receiver that listens while the transmitter fires will see that harmonic unless a filter is fitted, and a system with a strict spurious specification should plan the filter rather than measure and hope. The third harmonic at 28.2 GHz sits in the Ka band and matters for systems that share an aperture.
Flatness across 200 MHz is not published, but a matched module on a window this narrow is normally flat within a few tenths of a decibel, because the match is optimised for that window alone. That is the trade against the HXNM40012, which covers 8 to 12 GHz and moves further across its band.
The input return loss is also unpublished. At 24 dBm of drive a poor input match costs drive power and distorts the pulse envelope, so the driver should be isolated with a pad or a circulator as well. A three decibel pad in front of the module costs three decibels of drive and buys stability against the load pulling the driver.
Where 9.3 to 9.5 GHz is used
This window sits inside the X band radar allocation. Weather radar in several regions operates near 9.4 GHz, airborne mapping and ground surveillance radars use overlapping windows, and marine radar uses 9.3 to 9.5 GHz in many administrations. The common feature is a magnetron replacement or a solid state transmitter upgrade, where the old tube is being swapped for a module that needs no warm up and no high voltage supply.
A solid state replacement changes the transmitter architecture. The magnetron was a single device fed by a pulse transformer at several kilovolts; the module runs on 28 V, needs a driver and a sequencer, and delivers a much cleaner spectrum. The 25 W figure is also higher than most marine magnetrons of the same size class produce in average terms, which is why these upgrades usually gain range as well as reliability.
Defence datalinks and seekers also use this window. Those applications care about pulse fidelity and about the phase stability of the module across temperature, and the vendor publishes neither. A seeker programme should plan a phase measurement over temperature on the first articles rather than assume the module is phase stable because it is internally matched.
Our defence grade component page covers the documentation and traceability questions that come with radar work, and it is where a programme with a qualification file should begin.
Comparing HXNM40015 with the rest of the family
The HXNM40012 covers 8 to 12 GHz at 42 dBm with 20 dB of gain on the same rail. It is 2 dB down on this part and twenty times wider, and it is the correct choice when the radar has to work on more than one window or when the frequency plan is not fixed. This part is 2 dB stronger and confined to one channel, which is worth having when the link budget is the constraint.
The GaAs parts on nearby windows sit on 10 V. The HXC40039 to HXC40041 cover 9 to 10 GHz at 36 to 41 dBm compression with 7 to 8 dB of gain, and the HXC40042 reaches 44 dBm on the same window with 6 dB of gain. A GaAs part at 44 dBm compression with 6 dB of gain needs 38 dBm of drive, which is another power stage, so the GaN module wins on gain and on drive level even where the output is equal.
Our RF power transistor cross reference page sets out the sequence we use, rail then mode then band then output then gain, and it explains why a pulsed part cannot be treated as a continuous wave part with a lower average.
Questions buyers ask before ordering HXNM40015
What is the duty cycle? The vendor does not publish one. The row says pulse and stops there. We quote the part as a pulsed device and state the gap in writing, and the customer's pulse width and duty have to be confirmed against the factory before a schedule is set.
Is there a data sheet? No. The vendor publishes an index row and a product page with the same five electrical figures and the 50 ohm port impedance. There are no curves, no scattering parameters, no thermal data and no package drawing.
What has to be on the purchase order? The band, the 28 V rail, the pulse mode, the pulse width and the duty, plus the quantity. No orderable addendum, marking code or packing column is published, so reel size and moisture level come from the factory quotation.
How do we start? Send the pulse width, the duty cycle, the output required at the antenna connector and the drive available. We will confirm the fit, quote from the current factory schedule and ship a sample that has been run at the production pulse with the flange temperature recorded.