Contact Us

HXN50222

Brand: Hisiwell
Hisiwell HXN50222 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN50222 — Discrete & Power Semiconductors | Superb Automation

HXN50222

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN50222 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN50222: one hundred and forty watts of peak at 5 to 6 GHz on a 28 volt rail

The HXN50222 is a gallium nitride power transistor from Hisiwell filed on the 5 to 6 GHz window on a 28 V rail, with 140 W of peak output and a pulse mode on the index row. That is 51.46 dBm by calculation. It is the largest peak figure in the 5 GHz group and it arrives with almost no supporting rows: no power gain, no efficiency, no package, no pulse width, no duty cycle.

That is not a reason to skip the part, it is a reason to read it properly. A 140 W peak row on a 28 V rail sets a floor on the current whatever the efficiency is. At 100 per cent drain efficiency the drain would draw 5.0 A, which is physically impossible, so the real figure is a multiple of that. The table below gives the DC budget at four efficiency values so a system engineer can see the range before the factory answers.

The band is 1 GHz wide from 5 to 6 GHz, 18.2 per cent fractional at 5.5 GHz. For an unmatched part that is a moderate window, and it is the same window as the HXN50217 at 100 W and the HXN50214 at 50 W, so the three parts form a power ladder on one band with one network family.

The load voltage is the number that decides the match hardware. At 50 ohm, 140 W is 83.7 V RMS and 118.3 V peak. Most pulsed radar systems do not run 50 ohm at the device, they run 12.5 or 25 ohm, and at 12.5 ohm the peak falls to 59.2 V while the current doubles. Both are calculated rows on this page, and both are worth settling before the coupler is bought.

With no gain row published the drive power is unknown, and that is the one figure that decides whether the part drops into an existing line up or needs a new driver. It is the first question in the message to the factory.

The parameter rows behind the HXN50222

Part classGallium nitride HEMT power transistor, unmatched
Frequency range5 to 6 GHz
Band width, calculated1,000 MHz
Fractional bandwidth at 5.5 GHz centre, calculated18.2 per cent
Peak output, index row140 W
Peak in dBm, calculated51.46 dBm
Saturation output columnNot published
Average output columnNot published
Power gainNot published
Drain efficiencyNot published
Drain current at 100 per cent efficiency, calculated5.00 A, a floor and not a real figure
Drain current at 60 per cent, calculated8.33 A, 93.3 W of heat
Drain current at 50 per cent, calculated10.00 A, 140.0 W of heat
Drain current at 40 per cent, calculated12.50 A, 210.0 W of heat
DC input at 50 per cent, calculated280 W
Drain rail28 V
ModePulse
Pulse width and duty cycleNot published, and they set the average heat
Load voltage at 50 ohm, calculated83.7 V RMS, 118.3 V peak
Load voltage at 25 ohm, calculated59.2 V RMS, 83.7 V peak
Load voltage at 12.5 ohm, calculated41.8 V RMS, 59.2 V peak
Output per gigahertz of band, calculated140 W per GHz
MatchingUnmatched, network on the customer board
Package and bodyNot published on the index row
Thermal resistance, junction to caseNot published
Compression pointNot published

Ten amps at fifty per cent and twelve and a half at forty

The DC budget is a range, not a number, and the range is wide. At 50 per cent efficiency the drain draws 10 A and the part leaves 140 W of heat during the pulse. At 40 per cent it draws 12.5 A and leaves 210 W. At 60 per cent it draws 8.33 A and leaves 93 W. A supply sized at the optimistic end is a supply that sags on the first long pulse.

The heat figure has to be read with the duty cycle, and the duty cycle is not published. A 140 W pulse at 10 per cent duty leaves 14 W of average heat, which a flange handles. The same pulse at 30 per cent duty leaves 42 W, which needs a different sink. The pulse width matters for the transient thermal impedance, and no curve is published for it either.

The current is the second half of the same argument. Ten amps through a drain lead and a choke is a 300 mil trace at one ounce copper and a choke with a 15 A saturation rating, because the current at the crest plus the mismatch current is what saturates it. At 12.5 A the trace and choke move up another size.

The output impedance question is the one that saves money. At 50 ohm the peak is 118.3 V and the match components have to be rated above that. At 12.5 ohm the peak is 59.2 V and the same 100 V parts are comfortable, at four times the current. Pulsed radar systems normally run the low impedance for exactly this reason.

HXN50222 against the other peak parts on 5 to 6 GHz

HXN502225 to 6 GHz140 W peakNot publishedNot publishedReference point
HXN502175 to 6 GHz100 W peakNot publishedNot published1.46 dB less peak, continuous wave row
HXN502145 to 6 GHz50 W peakNot publishedNot published4.47 dB less peak
HX5060140P25 to 6 GHz140 W saturation11 dB50 per centSame output with gain and efficiency published
HXN503355 to 6 GHz70 W peakNot publishedNot published3.01 dB more peak than the 50 W member
HX2580258GX5.2 to 5.9 GHz25 W peak, 4 W average12 dB25 per centNarrower window, much lower output

The interesting row is the HX5060140P2. It carries the same 140 W at the same band and it publishes a gain of 11 dB and an efficiency of 50 per cent. If the two parts are related, and the numbers suggest they are, then this part is the pulse rated member of the same family and the missing rows can be filled from the sibling. That is a hypothesis and not a datasheet figure, so the page does not use it in any calculation.

Against the 100 W and 50 W members the ladder is clean: 1.46 dB between 140 and 100, 4.47 dB between 140 and 50. A system that needs 3 dB of margin on a 100 W requirement lands on the 140 W part, and the question becomes whether the pulse rated member can be cooled in the available space.

The 5 GHz shelf is indexed on the RF component sourcing page, and the way a peak rated part is qualified before a radar build starts is set out on RF power transistor cross reference.

Board notes for a one hundred and forty watt pulse stage

The first item is the duty cycle. A pulse rated part with no published pulse width and duty limit is a part whose average heat is unknown, and average heat is what sizes the sink. Ask for both before the enclosure is fixed.

The second item is the impedance. Running the device at 12.5 ohm keeps the peak voltage near 59 V and puts the current near 8.4 A per side at 140 W, which is a comfortable range for a low loss laminate and a 100 V capacitor.

The third item is the current path. At 10 to 12.5 A of drain current the choke, the feed trace and the ground return all have to be sized for the crest plus mismatch, and the decoupling bank has to hold the rail through the pulse rather than through the average.

The fourth item is gain. With no gain row, the drive power is unknown, so the first article is measured for gain at 5.0, 5.5 and 6.0 GHz before any driver is bought.

Questions buyers ask about HXN50222

Is 140 W continuous? No, the row is a peak figure with pulse mode. Continuous operation is the HX5060140P2 at the same band.

What is the efficiency? Not published. The DC budget on this page is given as a range across 40, 50 and 60 per cent so the supply can be sized before the factory answers.

What is the drive power? Not published, because no gain row exists. It is measured on the sample.

Can it run at 6 GHz? The row is 5 to 6 GHz, so 6 GHz is at the edge of the stated window and confirmed on a sample rather than assumed.

How do we start? Send the band, the pulse width, the duty cycle, the output at the connector, the impedance and the rail. We will confirm the missing rows with the factory, quote from the schedule and ship a sample measured under the intended pulse.