HXN40061
Product Specifications
HXN40061
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40061 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40061: five watts across the 5.3 to 5.9 GHz span
The HXN40061 is the entry member of the Hisiwell group that covers 5.3 to 5.9 GHz. The vendor index row reads 5.3 to 5.9 GHz, saturated output at least 37 dBm, gain at least 12 dB, drain efficiency at least 45 per cent, 28 V drain rail, plus or minus 0.8 dB of flatness, continuous wave. That is 5.01 W across 600 MHz, which is the widest window in the 5 GHz region of this catalogue.
The budget is modest at this power level. At 45 per cent efficiency 5.01 W of output draws 11.1 W from the rail, which is 0.398 A at 28 V, and leaves 6.1 W of heat. Those are calculated figures from the published rows, and they are small enough that a conventional board with a copper paddle and a few vias carries them without a separate carrier.
The drive for rated output is 25 dBm, which is 0.316 W. That is a level a packaged driver, a two stage discrete chain or even a high output synthesizer reaches directly, which makes this part usable as a single stage after the modulator in a small transmitter.
The band is the reason to look at it. 5.3 to 5.9 GHz covers the upper 5 GHz WLAN channels, the 5.8 GHz ISM allocation and the 5.85 to 5.925 GHz band used for vehicle to vehicle links. Six hundred megahertz at a 5.6 GHz centre is 10.71 per cent fractional bandwidth, which is wide for an internally matched part and wide enough that one amplifier covers several channel plans.
The parameter rows Hisiwell publishes for HXN40061
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 5.3 to 5.9 GHz |
| Bandwidth, calculated | 600 MHz, 10.71 per cent fractional at a 5.60 GHz centre |
| Saturation output power as published | at least 37 dBm |
| Saturation output power in watts, calculated | 5.01 W |
| Gain as published | at least 12 dB |
| Drain efficiency as published | at least 45 per cent |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Output at 1 dB compression | not published, the index prints a slash in that column |
| DC input at saturation, calculated | 11.1 W |
| Drain current at saturation, calculated | 0.398 A at 28 V |
| Dissipation at saturation, calculated | 6.1 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 7.5 W |
| Drive power for the rated output, calculated | 25 dBm, 0.316 W |
| Output per 100 MHz of the band, calculated | 0.84 W |
| Load voltage at saturation into 50 ohm, calculated | 15.8 V RMS, 22.4 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour on the same band at 40 dBm | HXN40062, same rail, same gain floor |
Ten point seven per cent bandwidth from an internally matched part
Internal matching is a compromise between bandwidth and gain. A narrow band match reaches higher gain and better efficiency, and a wide one gives up some of both. At 10.71 per cent this part sits on the wide side for its family, and the price shows in the gain floor: 12 dB here against 14 dB on the 0.9 to 1.2 GHz parts that are only a quarter as wide.
The practical value of 600 MHz is that a single board covers the 5.4 GHz and 5.8 GHz WLAN windows together. Two channels that would otherwise need two amplifiers and a switch become one amplifier and a filter, and the bill of materials loses a part that has its own insertion loss and its own failure mode.
The plus or minus 0.8 dB flatness figure is quoted across the whole window, which means the edges are included. A link budget built on the 37 dBm floor and the flatness together is the conservative reading, and it is the one to use when the antenna gain is fixed by a mechanical constraint rather than chosen for the electronics.
Where the system needs more output on the same span, the same vendor offers HXN43005 at 47 dBm with 10.5 dB gain and 52.4 per cent efficiency on 5.0 to 5.9 GHz. It covers a wider band at a higher power, and it gives up 1.5 dB of gain against this part.
Thermal and mechanical notes at five watts
6.1 W of dissipation is the point where a board level solution becomes practical. A carrier offering 5 C per watt rises 31 C over the case, and one offering 3 C per watt rises 18 C. With a 100 C case limit and a 70 C ambient both are comfortable, and with an 85 C ambient and a sealed enclosure the choice of carrier starts to matter.
The package outline is not published in text. One image appears on the vendor product page and no dimensioned drawing is offered, so the land pattern has to be taken from the image or from a sample. That is a real step in a first build and it should be on the schedule rather than discovered at the board build stage of a prototype.
The load voltage at 5.01 W into 50 ohm is 15.8 V RMS and 22.4 V peak, which is below the 28 V rail and therefore inside the rating of every ordinary SMA connector. A small part like this does not force the connector and cable selection the way a 50 W part does, and that is one less constraint on the enclosure.
The gate bias is not published either. First article work is a bias sweep against drain current with the part on a bench supply, and the quiescent point is chosen for the linearity the application needs rather than for a vendor recommendation, because there is none.
Applications where 5.3 to 5.9 GHz and five watts line up
The 5.8 GHz ISM band is used for point to point links, for industrial heating control and for short range telemetry. A 5 W amplifier at 45 per cent efficiency is a sensible final stage for a link of a few kilometres with a directional antenna, and the 600 MHz window leaves room for a frequency plan that avoids interference.
The 5.85 to 5.925 GHz allocation used for vehicle to vehicle and infrastructure links sits at the top of the window. A part specified to 5.9 GHz covers it with a small margin, and the flatness figure applies at the edge, which is where a link budget is tightest.
The upper 5 GHz WLAN channels also sit inside the window. For a test instrument that has to exercise those channels, one amplifier covering all of them is worth more than a narrow part with 2 dB more gain, because the instrument can then sweep the band rather than step through channels.
Where the product is a drone data link, the same window is used for the video downlink in several regions. Our drone and UAV components page covers the parts around this one, including the front end filters and the driver stages that set the overall link budget.
What to settle before the part goes on a board
The first item is the match at the band edges. The part is internally matched to 50 ohm at both ports according to the vendor description, and the flatness is quoted across the full window, so the external network can be a filter and a bias tee rather than a tuning network. That is a simplification worth planning for, because it removes the tuning step from the first article.
The second item is the bias sequence. With no published gate voltage window, the safe sequence is to apply the gate bias first, then the drain, and to remove the drain before the gate on power down. A part with an unmatched gate can draw destructive current if the drain arrives first.
The third item is packing. No addendum, no reel size and no moisture level are published, so the purchase order names the band, the rail and the quantity and the factory confirms the rest. For a production program the confirmation should include the moisture sensitivity level, because a part that needs baking changes the assembly flow.
Where the part is being evaluated against an existing 5 W stage from another vendor, the comparison has to include the drive level and the flatness window, not only the output. Our amplifier cross reference page sets out the comparison fields, including the ones the vendor does not publish and that therefore have to be measured.
Questions buyers ask about HXN40061
Is it linear enough for a modulated signal. The vendor publishes no compression point and no intermodulation data, so linearity has to be established on a bench. At 5 W saturation a backoff of 6 dB gives 1.26 W of average output, which is a typical operating point for a multicarrier signal and leaves 2.94 W of heat at an assumed 30 per cent efficiency in backoff.
Can it be paralleled for more power. Nothing in the vendor data addresses combining, and the internally matched input makes two parts share a splitter rather than a common gate network. A balanced pair with a 3 dB hybrid is the conventional way, and it costs 3 dB of combining loss.
How wide is the temperature range. Not published. Junction temperature is not published either, so the operating window has to be established by test or taken from the vendor on request. For a product that has to work at an 85 C ambient this is a question for the factory before the build is frozen.
What is the lead time. It comes through the RF component sourcing route, where this part is held with the rest of the 5 GHz family, and the schedule depends on the factory lot rather than on a distributor shelf. Where a build needs the part held in advance, the same route covers the reservation.