HXN40031
Product Specifications
HXN40031
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40031 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40031: 31.6 W of continuous wave on the 2.7 to 3.7 GHz band
The HXN40031 sits one step above the smallest member of the Hisiwell group that spans 2.7 to 3.7 GHz. It is the same band, the same 28 V rail and the same 12 dB gain floor, with the saturated output raised from 40 to 45 dBm, which is 31.6 W. The efficiency row is identical at 45 per cent, so the extra 5 dB of output costs 3.16 times the DC input and 3.16 times the heat.
That multiplication is the whole story of the part. At 45 dBm and 45 per cent the rail supplies 70.3 W, the drain current is 2.51 A at 28 V, and 38.7 W of heat has to leave a flange that is the same size class as the ten watt member. The drive at 12 dB of gain is 33 dBm, or 2 W, which is still inside the reach of a packaged driver stage.
What the part buys is headroom on a gigahertz wide band: 31.6 W at saturation with plus or minus 0.8 dB of flatness, continuous wave, 50 ohm at both ports. A continuous wave rating across a full gigahertz at this power is a different proposition from a pulsed part, because there is no duty cycle to hide behind. The 38.7 W is steady, and the case temperature is set by the heatsink rather than by a pulse width.
The vendor builds the family with in-plane matching synthesis on a film hybrid carrier, and this part is named as internally matched in the same way as the rest of the group. No tuning is offered or expected at either port, which is what makes a 30 per cent fractional bandwidth usable without a matching network on the board.
The parameter rows Hisiwell publishes for HXN40031
| Part class | Gallium nitride power transistor, internally matched |
| Frequency range | 2.7 to 3.7 GHz |
| Bandwidth, calculated | 1000 MHz, 31 per cent fractional |
| Saturation output power as published | at least 45 dBm |
| Saturation output power in watts, calculated | 31.6 W |
| Gain as published | at least 12 dB |
| Drain efficiency as published | at least 45 per cent |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | continuous wave |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Output at 1 dB compression | not published, the index prints a slash |
| DC input at saturation, calculated | 70.3 W |
| Drain current at saturation, calculated | 2.51 A at 28 V |
| Dissipation at saturation, calculated | 38.7 W |
| Dissipation if efficiency falls to 40 per cent, calculated | 47.4 W |
| Drive power for the rated output, calculated | 33 dBm, 2.00 W |
| Output per 100 MHz of the band, calculated | 3.2 W |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text, one image on the product page |
| Scattering parameters | not published |
| Pinch off voltage and gate bias point | not published on this page |
| Operating and storage temperature | not published |
| Moisture level and floor life | not published |
| Orderable addendum and packing | not published |
| Neighbour below on the same band | HXN40030 at 40 dBm, same rail |
| Neighbour above on the same band | HXN40032 at 49 dBm, 10 dB gain |
Thirty eight watts of steady heat on a 28 V rail
The thermal side is where this part differs from the ten watt member, and the difference is not linear in difficulty. Thirty eight point seven watts through a flange of this class, with a carrier at 3 C per watt, is 116 C of rise over the case before the ambient is counted, so the case has to be held near 40 C for a 100 C junction. That demands a metal block under the part, a thin thermal interface and a heatsink with a real thermal resistance, not a bare board with a copper pour.
The drain current is 2.51 A, which is modest for a 28 V rail and forgiving on the feed. The capacitor bank only has to hold the rail against a continuous draw rather than a pulse, so the question is decoupling at the band rather than energy storage, and a well laid out feed with a few hundred picofarads close to the flange does that work.
Efficiency is the variable that cannot be fixed by the board. At 40 per cent the heat rises to 47.4 W and the current to 2.82 A, which is a different cooling class on the same flange. With no minimum efficiency printed, a purchase specification that asks for 45 per cent and receives a part at the bottom of the spread has to be able to remove 9 W more than it planned for.
Continuous wave at 31.6 W is also the case where the compression point matters most. A constant envelope waveform can run near saturation; a modulated one cannot, and the index prints a slash in the compression column for this part. Any system that needs 45 dBm of average power with a peak to average ratio needs a device rated above this one, and the family offers 49 dBm on the same band.
What the page leaves to the first article
There is no data sheet for this part. The vendor publishes a nine column index and a short product page that repeats five of those rows, and the product page for this part adds no curve, no drawing and no bias table. Gain against frequency, return loss, isolation and compression are all absent, which means the flatness row is the only description of behaviour across the gigahertz and it is stated for saturated output only.
The bias window is the same gap as elsewhere in the family. The one full document, the HX2734P600W sheet reachable from the HXN42001 page, prints a pinch off window of minus 1.5 to minus 3.5 V and a 5 V gate ceiling. On this part that is a starting point for a first article, and the drain current at quiescence has to be set on the bench rather than taken from a table that does not exist.
The mechanical rows are absent as well: one outline image, no dimensions, no recommended torque. At 38.7 W of steady dissipation the mounting method is not a detail, because a flange that is not flat against its carrier loses the only heat path the part has.
What the page does give is enough to size a system: 45 dBm, 12 dB, 45 per cent, 28 V, plus or minus 0.8 dB, continuous wave. Those six values decide the supply, the driver, the heatsink and the band plan, and the rest is measurement.
Where a 31.6 W octave amplifier fits
The natural fit is a continuous wave transmitter or a test amplifier over 2.7 to 3.7 GHz where 31.6 W is enough: a short range radar with a continuous wave mode, a fixed link driver, an antenna range amplifier, or a laboratory source for component testing at 3 GHz. The octave band means one unit covers several allocations, and the 50 ohm ports mean the instrument can be built without a matching network.
It is also a driver for the 158.5 W member of the same band. That part needs 10 W at its 12 dB floor, and this one delivers 31.6 W, so a chain built on this part has 5 dB of margin against cable and isolator loss, which is the right way round for a production build.
It is a poor fit for continuous wave at the top of the band with a passive heatsink, for any application that needs a published compression point, and for a build where the flange cannot be bolted to metal. Our RF power transistor cross reference work lists the four 2.7 to 3.7 GHz outputs side by side with the heat each one brings, so the step from 31.6 W to 158.5 W can be priced against the heatsink rather than the headline.
Questions we answer on HXN40031 before a lot is booked
The first is the case temperature the system can hold. At 38.7 W the answer decides whether this part works at all, and it has to be agreed before the mechanical stack is frozen.
The second is the lot. No marking code, no moisture level and no orderable addendum are published, so the purchase order names the band, the rail and the mounting, and the incoming inspection plan records the flange, the marking and the gate and drain behaviour of every lot. A saturated power sweep at 3.2 GHz is done on the customer bench or at a partner RF laboratory.
The third is the bias supply order. Our RF procurement process sets the negative gate supply, the drain sequencing and the current limit in front of the vendor before the first lot, because a continuous wave part at this power has no duty cycle to protect it from a bias mistake.