HXN40010
Product Specifications
HXN40010
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN40010 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN40010: 53 dBm from 28 V in 1 ms pulses at 10 per cent duty
The HXN40010 changes two rows at once compared with the continuous wave members below it. The rail drops to 28 V and the operating mode becomes pulsed, with the vendor's table printing 1 ms at 10 per cent duty. The published figures are at least 53 dBm of saturation power, at least 13 dB of gain, at least 50 per cent efficiency, 50 ohm ports and plus or minus 0.8 dB of flatness across 1.2 to 1.4 GHz.
Fifty three dBm is 199.5 W, and 28 V is a rail that comes from a standard 28 V aircraft or vehicle bus rather than from a 50 V supply. At 50 per cent efficiency the DC input at saturation is 399 W, the drain current is 14.25 A, and the heat is 199.5 W. Those are peak figures inside a 1 ms pulse; the average values at 10 per cent duty are 399 W of DC input refilled at 39.9 W, 1.43 A of average drain current and 19.95 W of average dissipation.
That difference between 200 W peak and 20 W average is the entire point of a pulsed part. The die has to survive 200 W for a millisecond, and the carrier only has to remove 20 W on average, so a copper carrier and a modest heatsink become sufficient where the continuous wave 126 W member needed liquid cooling. The 28 V rail also keeps the peak drain current at 14.25 A rather than the 15.9 A a 50 V part draws for a higher output, which matters for the DC feed and the decoupling.
The drive is 40 dBm, which is 10 W. That is exactly the saturation output of the 40 dBm member of the same family, so a 200 W pulsed stage is normally driven by a 10 W continuous wave device driven 5 dB back, and the whole chain runs on two rails, 28 V for the final stage and 32 V for the driver. Two rails is one more supply than anybody wants, and the family offers a 32 V continuous wave member at 51 dBm for systems that would rather have one.
The parameter rows the vendor publishes
| Part class | Gallium nitride power transistor with internal matching |
| Frequency range | 1.2 to 1.4 GHz |
| Saturation power as published | at least 53 dBm |
| Saturation power in watts, calculated | 199.5 W |
| Gain as published | at least 13 dB |
| Efficiency as published | at least 50 per cent |
| Output at 1 dB compression | not published |
| Input impedance | 50 ohm |
| Output impedance | 50 ohm |
| Drain voltage | 28 V |
| Flatness across the band | plus or minus 0.8 dB |
| Operating mode | pulsed, 1 ms at 10 per cent duty |
| DC input at saturation during the pulse, calculated | 399 W |
| Dissipation during the pulse, calculated | 199.5 W |
| Drain current during the pulse, calculated | 14.25 A |
| Average DC input at 10 per cent duty, calculated | 39.9 W |
| Average dissipation at 10 per cent duty, calculated | 19.95 W |
| Average drain current at 10 per cent duty, calculated | 1.43 A |
| Drive power for rated output, calculated | 40 dBm, 10 W |
| Droop across the pulse | not published |
| Maximum pulse width and duty cycle | 1 ms at 10 per cent as published |
| Matching technology | in-plane matching synthesis on a film hybrid carrier |
| Stated application | RF and microwave systems |
| Package and flange | not published on the parameter page |
| Thermal resistance | not published |
| Scattering parameters | not published |
| Orderable addendum | not published |
| Member below, higher rail, continuous wave | HXN40009 at 51 dBm from 32 V |
| Member above, higher rail, pulsed | HXN40011 at 56 dBm from 50 V |
| Same band and mode, lower power | HXN40006 at 56 dBm over 0.9 to 1.4 GHz pulsed |
What a 1 ms pulse asks of the die and of the board
A millisecond is a long time in a power device. Thermal diffusion through a GaN die a hundred micrometres thick takes tens of microseconds, so a 1 ms pulse heats the whole die and part of the die attach, and the peak junction temperature inside the pulse is set by the transient thermal impedance rather than by the steady state path. The vendor publishes neither the transient impedance curve nor the steady state figure, so the peak junction temperature of a 1 ms, 200 W pulse cannot be computed from this page at all.
The average side is easier. At 10 per cent duty the 199.5 W of peak dissipation averages to 19.95 W, and 19.95 W through a carrier and interface adding up to 1.5 C per watt is 30 C of rise, which a 60 C cabinet turns into a 90 C average junction. If the transient peak on top of that average stays inside the channel limit, the build closes; that if is the one the missing curves would answer.
The pulse also has an electrical side. A 14.25 A drain current switched on in a microsecond, through a 28 V rail with any feed inductance, produces a drain excursion that the die has to absorb, and a 1 ms pulse is long enough for the current to reach its full value before the pulse ends. The decoupling network for a pulsed stage at this current is a bank of ceramic capacitors placed at the flange, not at the connector.
Where the datasheet stops and the bench starts
No transient thermal impedance is published, which is the single figure a pulsed part most needs. No droop figure is published either, so the output at the end of the 1 ms pulse relative to its start is unknown. Droop is what sets the usable pulse width in a radar or a pulsed data link, and a 1 ms pulse at 200 W is exactly where the drain capacitor and the bias network discharge starts to show.
There is no compression point and no small signal data, as on every member of this family, and no bias information. The 10 per cent duty is printed without a tolerance, which matters because a build that runs 15 per cent to gain range is outside the published condition and has no data behind it.
The mechanical data is absent again: no flange, no outline, no mounting specification. For a pulsed part the peak junction temperature depends on that interface, so the same device on two carriers is two different products.
Where a 200 W pulsed L band part still fits
It fits a 28 V pulsed transmitter, which is the standard rail in airborne and vehicle systems, and it fits a radar or a pulsed data link where 1 ms at 10 per cent is the actual waveform. It also fits a laboratory pulse source, where the average dissipation of 20 W can be handled by a bench heatsink and the 200 W peak is what the test needs.
It does not fit continuous wave operation, and the trap is a build that runs 5 per cent duty in test and 20 per cent in the field. It does not fit a linear application, and it does not fit a system that wants a single 32 V rail, since the 51 dBm member runs on 32 V and this one on 28 V. Choosing between them is a supply architecture decision that is much cheaper to make before the board than after it.
Our defense grade components page covers the traceability and documentation that a pulsed L band device normally carries into a programme, and the RF power transistor cross reference work holds the rail and the duty cycle as hard attributes, because those two rows, not the output power, decide which member of this family a system can actually use.
Questions we answer before an order is placed
The first is the waveform, in full: pulse width, duty cycle, and whether the field waveform matches the test waveform. The second is the rail architecture, since 28 V here against 32 V in the continuous wave members decides the supply count. The third is the drive, at 40 dBm, which is a 10 W stage in its own right and is normally the 40 dBm member of the same family.
The fourth is the thermal path. A pulsed part is often treated as a low heat part, and at 20 W average that is fair; at 20 per cent duty the same device averages 40 W and the carrier that was adequate is suddenly not. Ask for the highest duty the product can ever see, not the nominal one.
The fifth is the measurement route. RF power and pulse droop are measured on the customer bench or at a partner RF laboratory, while our test covers DC parameters, functionality and customer fixtures. Our incoming inspection plan records what the delivered lot carries, and the pulse data request is raised with the vendor before a first lot ships.