CDR14BP272AJSM KYOCERA AVX RF Capacitor
Product Specifications
PRODUCT SPECIFICATIONS
CDR14BP272AJSM — KYOCERA AVX RF/Microwave Capacitor
Product Overview
The CDR14BP272AJSM is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
Technical Specifications
| Part Number | CDR14BP272AJSM |
| Manufacturer | KYOCERA AVX |
| Frequency Range | GHz / Microwave (Series Dependent) |
| Q Factor | High Q (Series Dependent) |
| RF Suitable | YES |
| High Q | YES |
| Low Loss | YES |
| Tolerance | Refer to datasheet |
| Package / Case Style | Refer to datasheet |
| Dielectric Material | Refer to datasheet |
| Temperature Coefficient | Refer to datasheet |
| Operating Temperature Range | Refer to datasheet |
| Termination Finish | Refer to datasheet |
| Mounting Type | Surface Mount (SMD/SMT) |
| RoHS Compliance | RoHS Compliant |
| REACH Compliance | REACH Compliant |
| Country of Origin | United States |
| Manufacturer Part Number | CDR14BP272AJSM |
| Data Confidence | Series Based |
| Verification Note | Requires ATC datasheet confirmation |
Key Features
- High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
- Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
- RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
- Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
- Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.
Applications
- RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
- Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
- Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
- Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
- Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.
Compatible and Alternative Part Numbers
- Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
- Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
- Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)
About KYOCERA AVX
KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.
About Superb Automation — Trusted KYOCERA AVX Supplier
Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.
Why Source CDR14BP272AJSM from Superb Automation?
- Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
- Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
- Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
- Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
- One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
- Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
- Global Logistics — International shipping with full export documentation.
Ordering Information
To order CDR14BP272AJSM or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com
CDR14BP272AJSM: 2700 pF at 50 V in the CDR14 outline
Six fields sit inside CDR14BP272AJSM and none of them is a preference: style CDR14, dielectric BP, 272 is the capacitance code, two significant digits and a count of zeros, which reads 2700 pF, voltage letter A for 50 VDC, tolerance J for plus or minus 5 percent, termination S and failure rate M at 1.0 percent. Change one letter and the part on the drawing is a different part, which is why the order is checked against the number and not against the family name. A wrong style letter fits nothing on the board, and a wrong dielectric letter tunes to another place.
| Style and outline | CDR14, military style in the 0.110 inch square outline |
| Dielectric | BP, zero plus or minus 30 ppm per degree C |
| Capacitance | 2700 pF, code 272 |
| Tolerance | J, plus or minus 5 percent, a window of 2565 to 2835 pF |
| Rated voltage | 50 VDC, voltage letter A |
| Termination | S, solder coated final with a minimum of 4 percent lead |
| Failure rate level | M, 1.0 percent |
| Qualification | MIL-PRF-55681, slash sheet 4 covers styles CDR11 to CDR14 |
| Style capacitance range | 0.1 pF to 5100 pF, 200 and 500 V on the small values |
| Body length | 2.79 plus 0.889 minus 0.508 mm |
| Body width | 2.79 plus or minus 0.508 mm |
| Body thickness | 0.762 to 2.59 mm |
| Termination band | 0.127 to 0.635 mm |
| Operating range | minus 55 to plus 125 degrees C with and without rated voltage |
| Temperature drift over the range | about 14.6 pF at 30 ppm per degree C |
| Reactance at 150 MHz | 0.39 ohm nominal |
| Reactance at 1 GHz | 0.06 ohm nominal |
| Reactance at 2.45 GHz | 0.02 ohm nominal |
| Stored energy at rated voltage | 0.0 nanojoule at 50 V |
| Packing | waffle pack 80 pcs, or tape and reel 2000 pcs on a 7 inch reel |
CDR14 carries the 0.110 inch square outline: 2.79 plus 0.889 minus 0.508 mm by 2.79 plus or minus 0.508 mm, with a body between 0.762 to 2.59 mm and a termination band running from 0.127 to 0.635 mm. The dielectric BP is coefficient limited rather than value limited, so the 2700 pF part at 50 V sits inside a family that holds its coefficient across the whole range.
Because CDR14 is a chip ceramic, the tolerance letter is the only field that moves the electrical window: on 2700 pF it gives plus or minus 5 percent, or 2565 to 2835 pF. The voltage field A fixes the rating instead, and the two are read side by side on the receiving dock.
CDR14 body, termination and packing
Mechanically the 2700 value at 50 V is a 0.110 inch square body, 2.79 plus 0.889 minus 0.508 mm by 2.79 plus or minus 0.508 mm, with the band between 0.127 to 0.635 mm. A reel of these is picked and placed like any chip, and the outline letter is what tells the placement program which nozzle and which pocket to expect.
On the finish, S reads solder coated final with a minimum of 4 percent lead. Nothing in the electrical table changes with it, but the assembly and the inspection plan do, and on a programme with a fixed profile that letter is the first thing checked after the value.
Dielectric and rating at 50 V
The electrical identity of CDR14BP272AJSM is one coefficient over one range: zero plus or minus 30 ppm per degree C from minus 55 to plus 125 degrees C, printed with and without the rated voltage applied. On 2700 pF that comes to about 14.6 pF of drift across the range, small against the plus or minus 5 percent window the tolerance letter allows.
On CDR14BP272AJSM the voltage field A is the whole rating statement at 50 V, and the failure rate letter M at 1.0 percent is the screening statement. The sheet gives typical loss curves for the family instead of a printed ESR ceiling, so a 2700 pF part in a loss sensitive position is judged on that curve rather than on a single number.
What 2700 pF does from 30 MHz to 2.45 GHz
Read as reactance the 2700 pF part at 50 V is 1.96 ohm at 30 MHz, 0.39 ohm at 150 MHz, 0.12 ohm at 500 MHz, 0.06 ohm at 1 GHz and 0.02 ohm at 2.45 GHz, so against 50 ohm it is already below 50 ohm at the bottom of the band, because the crossing sits at about 1.2 MHz. Below self resonance the body behaves as a capacitor and the figure falls with frequency, above it the same body turns inductive. The figures above are computed at the printed value, so they move with the tolerance letter in the same proportion.
One more figure settles the application: into 50 ohm the 2700 pF part reaches its half power point at 1.2 MHz, where reactance equals load. A 50 V stage that has to work below that point needs a larger value, and one that works above it can use this body as a coupling element, with 0.39 ohm at 150 MHz left in the line.
The sheet prints typical Q and ESR curves by frequency and by capacitance, and it prints no single ohmic limit and no amperage for this family. On a 2700 pF part at 50 V that means the loss budget is read off the curve for the value and the mounting, and a stage that pushes current through the part is quoted from that curve rather than from a number.
At 50 V the 2700 pF body holds 0.0 nanojoule and 135 nanocoulomb. Both are small, and both are the reason this value is used in signal and matching positions rather than in energy storage, where the same outline would be the wrong purchase.
Sourcing the 2700 pF value and the second source
A 2700 pF part at 50 V arrives either in a 80 piece waffle pack or on tape and reel, 2000 pieces on a 7 inch reel and 10,000 on a 13 inch reel. RF Component Sourcing, BOM Shortage Recovery, Incoming Inspection Plan holds the sourcing path, and a second source is matched on capacitance, tolerance, voltage, dielectric and outline before a sample is released, because a different outline changes the pad and a different dielectric changes the coefficient.
For a 2700 pF value rated at 50 V the order needs five fields and one packing quantity, and nothing else on this page moves the price of a package. Incoming inspection then reads the marking, measures against the plus or minus 5 percent window from 2565 to 2835 pF, and confirms the voltage letter on the label.
Package and lot records travel with the 2700 pF part at 50 V, because a body this small is hard to confirm on a meter that was not zeroed. The order records the packing code, the date code and the quantity, and the incoming check is written against those fields so a later build traces back to the same lot.