800E471FT3600X KYOCERA AVX RF Capacitor
Product Specifications
PRODUCT SPECIFICATIONS
800E471FT3600X — KYOCERA AVX RF/Microwave Capacitor
Product Overview
The 800E471FT3600X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
Technical Specifications
| Part Number | 800E471FT3600X |
| Manufacturer | KYOCERA AVX |
| Frequency Range | GHz / Microwave (Series Dependent) |
| Q Factor | High Q (Series Dependent) |
| RF Suitable | YES |
| High Q | YES |
| Low Loss | YES |
| Tolerance | Refer to datasheet |
| Package / Case Style | Refer to datasheet |
| Dielectric Material | Refer to datasheet |
| Temperature Coefficient | Refer to datasheet |
| Operating Temperature Range | Refer to datasheet |
| Termination Finish | Refer to datasheet |
| Mounting Type | Surface Mount (SMD/SMT) |
| RoHS Compliance | RoHS Compliant |
| REACH Compliance | REACH Compliant |
| Country of Origin | United States |
| Manufacturer Part Number | 800E471FT3600X |
| Data Confidence | Series Based |
| Verification Note | Requires ATC datasheet confirmation |
Key Features
- High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
- Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
- RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
- Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
- Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.
Applications
- RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
- Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
- Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
- Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
- Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.
Compatible and Alternative Part Numbers
- Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
- Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
- Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)
About KYOCERA AVX
KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.
About Superb Automation — Trusted KYOCERA AVX Supplier
Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.
Why Source 800E471FT3600X from Superb Automation?
- Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
- Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
- Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
- Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
- One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
- Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
- Global Logistics — International shipping with full export documentation.
Ordering Information
To order 800E471FT3600X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com
800E471FT3600X: 470 pF at 3600 V in the case E outline
Read 800E471FT3600X from the left and the string is already settled. 800E names the series, the E is case E at 0.380 inch square, 471 is the capacitance code, two significant digits and a count of zeros, which reads 470 pF, F holds the window at plus or minus 1 percent, T is the tin plated nickel barrier termination, 3600 is the working voltage in volts DC and X is the laser marking. The packing letter is the one field the number leaves open, so it is written on the order rather than inside the part number.
| Series and case | 800E in case E, a 0.380 inch square outline, 9.65 mm by 9.65 mm overall |
| Capacitance | 470 pF, code 471 |
| Tolerance | F, plus or minus 1 percent, a window of 465 to 475 pF |
| Working voltage | 3600 VDC, 2545 V RMS on a sine wave |
| Dielectric withstanding | 4320 V for five seconds, 120 percent of the working voltage |
| Life test | 3600 V for 2000 hours at 125 degrees C, 100 percent of the working voltage |
| Temperature coefficient | zero plus or minus 30 ppm per degree C, minus 55 to plus 125 C |
| Operating range | minus 55 to plus 125 degrees C, no derating of working voltage |
| Quality factor | greater than 5,000 at 1 MHz, the figure the sheet prints for 3.3 to 1000 pF |
| Insulation resistance at 25 C | 10^5 Mohm minimum, tested at 500 VDC maximum |
| Insulation resistance at 125 C | 10^4 Mohm minimum, tested at 500 VDC maximum |
| Outline | 0.380 plus 0.015 minus 0.010 inch, 9.65 plus 0.38 minus 0.25 mm on each side |
| Termination overlap | 0.040 inch, 1.02 mm maximum, on every value in the case |
| Terminal strength | 10 lbs minimum and 25 lbs typical for five seconds, MIL-STD-202 method 211 |
| Drift and retrace | plus or minus 0.02 percent or 0.02 pF, whichever is greater |
| Aging and piezoelectric effects | none stated for both on this sheet |
| Stored energy | 3.05 millijoule at 3600 V, from one half C V squared |
| Stored charge | 1692 nanocoulomb at 3600 V |
| Reactance at 150 MHz | 2.26 ohm nominal |
| Packing | tape and reel 250 pieces, tray 24 or 96, tray 16 or 32, box of 20 |
One capacitance range is printed for the series, 3.3 pF to 5100 pF, and one operating range for all of it, minus 55 to plus 125 degrees C with no derating of working voltage. What changes down the table is the voltage each value is offered at, so the 470 pF part at 3600 V is a specific line on the values table and not a general example.
Nothing in 800E471FT3600X is free once the drawing exists: case letter, capacitance code, tolerance and voltage field all have to match, and only the packing letter at the end is a choice. On the 470 pF part at 3600 V the acceptance window is plus or minus 1 percent, written as 465 to 475 pF, and the rating the board has to survive is 3600 V.
Case E body and the horizontal pad for 470 pF
The outline is 0.380 inch square, 9.65 mm with plus 0.38 and minus 0.25 mm, with 1.02 mm of termination overlap at each end. That is the largest case in the 800 family, so the 470 pF part at 3600 V changes what the placement nozzle and the reflow profile have to carry, not only what the pad drawing says.
There is no vertical mount row for this case, so the 470 pF part at 3600 V is always laid flat and the only choice is normal or high density: A 10.29, B 1.27, C 8.26 and D 10.80 mm against A 9.73, B 0.76, C 8.26 and D 9.78 mm. The 1.02 mm overlap is where the solder fillet forms at both ends, and the tight row does not shrink it.
Electrical limits at 3600 VDC
The electrical identity of 800E471FT3600X is a zero plus or minus 30 ppm per degree C coefficient over minus 55 to plus 125 degrees C, no derating across that range, greater than 5,000 at 1 MHz, the figure the sheet prints for 3.3 to 1000 pF, and a withstanding test at 4320 V for five seconds, which is 120 percent of the rating. Life test runs 2000 hours at 125 degrees C at 3600 V, 100 percent of the rating on a 3600 V part.
The environmental block is MIL-STD-202 in four places: method 107 condition A for thermal shock, method 106 for moisture resistance, method 103 condition A for low voltage humidity at 85 degrees C and 85 percent for 240 hours with 1.5 VDC applied, and method 108 for the 2000 hour life test. None of it changes with the value, so the 470 pF part at 3600 V inherits the same schedule.
What 470 pF does from 30 MHz to 1 GHz
At 30 MHz the 470 pF body at 3600 V presents 11.3 ohm, at 150 MHz 2.26 ohm, at 500 MHz 0.68 ohm and at 1 GHz 0.34 ohm, and on a 50 ohm line the value reaches 50 ohm at about 6.8 MHz, inside the band. Those four numbers are what a coupling, bypass or tuning position is built around. The F window of 465 to 475 pF reads 2.24 ohm at the top and 2.28 ohm at the bottom against 2.26 ohm nominal at 150 MHz, a spread of 0.05 ohm, 2.0 percent of nominal on a 3600 V part.
The loss statement for the 470 pF part at 3600 V is greater than 5,000 at 1 MHz, the figure the sheet prints for 3.3 to 1000 pF, and the sheet stops there: no ESR ceiling and no current rating are printed for case E, so an amplifier stage at 3600 V is checked on Q, on the mounting and on the cooling path instead of on a single amperage.
A 470 pF part at 3600 V held to zero plus or minus 30 ppm per degree C drifts about 2.5380 pF from minus 55 to plus 125 degrees C, which is 0.012 ohm against the 2.26 ohm nominal at 150 MHz. On a 3600 V stage that figure is small next to the tolerance window, and the two are read together when a tuned position is signed off.
Sourcing the 470 pF value and the second source
Because 800E471FT3600X ends at the marking field, packing is quoted with the order: T for tape and reel at 250 pieces, J24 or J96 on a tray of 24 or 96, J16 or J32 on a tray of 16 or 32, or B20 in a box of 20. On a 470 pF order at 3600 V that count sets how many boards one package covers. RF Component Sourcing, Component Lead Time Solutions, Kitting Service covers the sourcing side for a board that needs its other RF parts as well.
At 3600 V and 470 pF the buying question is not only price: package size, date code and storage grade set what the line can run. A replacement is checked on the four fields the order code exposes, capacitance, tolerance, voltage and case, and only then on the certificate.
For the 470 pF value at 3600 V the sourcing conversation is short once the drawing is in hand: capacitance code, tolerance letter, voltage field and case, then the packing quantity. Everything after that is date code, packing and freight, and those are quoted rather than assumed.