Contact Us

800C182JT600X KYOCERA AVX RF Capacitor

Brand: ATC
The 800C182JT600X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
quote now

Product Specifications

PRODUCT SPECIFICATIONS

800C182JT600X — KYOCERA AVX RF/Microwave Capacitor

Product Overview

The 800C182JT600X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.

Technical Specifications

Part Number800C182JT600X
ManufacturerKYOCERA AVX
Frequency RangeGHz / Microwave (Series Dependent)
Q FactorHigh Q (Series Dependent)
RF SuitableYES
High QYES
Low LossYES
ToleranceRefer to datasheet
Package / Case StyleRefer to datasheet
Dielectric MaterialRefer to datasheet
Temperature CoefficientRefer to datasheet
Operating Temperature RangeRefer to datasheet
Termination FinishRefer to datasheet
Mounting TypeSurface Mount (SMD/SMT)
RoHS ComplianceRoHS Compliant
REACH ComplianceREACH Compliant
Country of OriginUnited States
Manufacturer Part Number800C182JT600X
Data ConfidenceSeries Based
Verification NoteRequires ATC datasheet confirmation

Key Features

  • High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
  • Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
  • RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
  • Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
  • Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.

Applications

  • RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
  • Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
  • Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
  • Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
  • Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.

Compatible and Alternative Part Numbers

  • Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
  • Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
  • Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)

About KYOCERA AVX

KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.

About Superb Automation — Trusted KYOCERA AVX Supplier

Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.

Why Source 800C182JT600X from Superb Automation?

  1. Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
  2. Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
  3. Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
  4. Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
  5. One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
  6. Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
  7. Global Logistics — International shipping with full export documentation.

Ordering Information

To order 800C182JT600X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com

800C182JT600X: 1800 pF at 600 V in the case C high RF power body

Field by field, 800C182JT600X reads series 800C, case C, 182 is the capacitance code, two significant digits and a count of zeros, which reads 1800 pF, tolerance J giving plus or minus 5 percent, termination T over a nickel barrier, a voltage field of 600 and laser marking X. The sheet makes one NPO dielectric and one case from 2.2 pF to 3000 pF, and the 1800 pF value at 600 V is one line on that table rather than a general example.

Series and case800C in case C, the 0.250 inch square high RF power body
Capacitance1800 pF, code 182
ToleranceJ, plus or minus 5 percent, a window of 1710 to 1890 pF
Working voltage600 VDC, 424 V RMS on a sine wave
Dielectric withstanding900 V for five seconds, 150 percent of the rating above 500 V up to 1250 V
Life test720 V for 2000 hours at 125 C, 120 percent of the rating above 500 V up to 1250 V
Temperature coefficientzero plus or minus 30 ppm per degree C, minus 55 to plus 125 C
Operating rangeminus 55 to plus 125 degrees C, no derating of working voltage
Quality factorgreater than 2,000 at 1 MHz across the whole 2.2 to 3000 pF range
ESR limit0.0005 ohm maximum at 1 MHz, the figure the sheet prints for above 10 pF
Insulation resistance at 25 C10^5 Mohm minimum at the rated working voltage, test capped at 500 VDC
Insulation resistance at 125 C10^4 Mohm minimum at the rated working voltage, test capped at 500 VDC
Body length0.230 plus 0.025 minus 0.010 inch, 5.84 plus 0.64 minus 0.25 mm
Body width0.250 plus or minus 0.015 inch, 6.35 plus or minus 0.38 mm
Body thickness0.200 inch, 5.08 mm maximum, on every value in the case
Termination overlap0.040 inch, 1.02 mm maximum, tin over nickel barrier
Terminal strength10 lbs minimum and 20 lbs typical for five seconds, MIL-STD-202 method 211
Drift and retraceplus or minus 0.02 percent or 0.02 pF, retrace none, aging none
Stored energy324 microjoule at 600 V, from one half C V squared
Reactance at 150 MHz0.59 ohm nominal

Across 2.2 pF to 3000 pF the body stays case C and the NPO dielectric stays the same, while the value and the rated voltage change line by line. On the 1800 pF value this page carries 600 V with a J window, and those two fields are what the goods in check reads against the label.

Because 800C182JT600X stops at the marking field, the packing code is quoted with the order and nothing else is left loose. For the 1800 pF value at 600 V the three fields read at goods in are the capacitance code 182, the tolerance letter J and the voltage field 600, and all three sit inside the part number.

Case C body and the tin over nickel barrier on 1800 pF

Mechanically the 1800 pF value at 600 V is a case C body with 0.040 inch, 1.02 mm, of termination overlap at each end, tin plated over a nickel barrier. Terminal strength is printed as 10 lbs minimum and 20 lbs typical for five seconds to MIL-STD-202 method 211, so a 600 V part of this size takes a pull that a fixture has to stay under when the board is clamped for test.

Printed as inches and millimetres the case reads 0.230 by 0.250 by 0.200, which is 5.84 by 6.35 by 5.08 mm at the maximum on each field. On the 1800 pF part at 600 V the assembly drawing names the pad, and the pad has to leave 1.02 mm of barrier exposed at each end for the fillet.

Electrical limits at 600 VDC

On 800C182JT600X the voltage story is a 600 V rating, a withstanding test at 900 V for five seconds, the 150 percent tier the sheet prints for anything above 500 V up to 1250 V, and a 2000 hour life test at 125 degrees C held at 720 V, the 120 percent figure for the same range. Around that the sheet fixes a 30 ppm per degree C coefficient and plus or minus 5 percent.

Receiving inspection on a 1800 pF part at 600 V usually starts with drift and retrace, plus or minus 0.02 percent or 0.02 pF, whichever is greater, because it bounds what a tuned stage sees after a thermal cycle. Retrace, aging and piezoelectric effects are all stated as none, and the sheet names no EIA-198, MIL-PRF-55681 or QPL listing.

What 1800 pF does from 30 MHz to 1 GHz

Read as reactance the 1800 pF part at 600 V is 2.95 ohm at 30 MHz, 0.59 ohm at 150 MHz, 0.18 ohm at 500 MHz and 0.09 ohm at 1 GHz, and against 50 ohm it reaches 50 ohm at about 1.8 MHz, inside the band. Below self resonance the body behaves as a capacitor and the figure falls with frequency, above it the same body turns inductive. The J window of 1710 to 1890 pF reads 0.56 ohm at the top and 0.62 ohm at the bottom against 0.59 ohm nominal at 150 MHz, a spread of 0.06 ohm, 10.0 percent of nominal on a 600 V part.

At 600 V the 1800 pF value holds 0.59 ohm at 150 MHz and its loss budget is greater than 2,000 at 1 MHz with ESR capped at 0.0005 ohm, 0.5 milliohm, for above 10 pF. Because no amperage is printed, the current a 1800 pF body can carry at 600 V is read from the supplier curve for the mounting.

Temperature is the other half of the frequency picture. The coefficient is zero plus or minus 30 ppm per degree C, so a 1800 pF part at 600 V moves by about 9.7200 pF over the full minus 55 to plus 125 degrees C range, which at 150 MHz is 0.003 ohm on top of the accepted window.

Sourcing the 1800 pF value and the second source

A 1800 pF part at 600 V ships on tape and reel at 500 pieces, on a tray of 36, 180, 24 or 60, or in a box of 24, and the packing code is a line on the order rather than a field inside the part number. Component Lead Time Solutions, Pin to Pin Cross Reference, Kitting Service holds the sourcing path, and a second source is matched on capacitance, tolerance, voltage and case before a sample is released, because another case changes the pad and a wider tolerance changes the window.

For a 1800 pF value rated at 600 V the order needs the capacitance code, the tolerance letter, the voltage field and a packing quantity, and nothing else changes the price of the package. Incoming inspection then reads the marking, measures against the J window and confirms the voltage field on the label.

Package and lot records travel with the 1800 pF part at 600 V, because a value this small at this voltage is hard to confirm on a meter that was not zeroed. The order records packing code, date code and quantity, and the incoming check is written against those fields so a later build traces back to the same lot.