Contact Us

800A1R5DT250X KYOCERA AVX RF Capacitor

Brand: ATC
The 800A1R5DT250X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX, part of the 800A series., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
quote now

Product Specifications

PRODUCT SPECIFICATIONS

800A1R5DT250X — KYOCERA AVX RF/Microwave Capacitor

Product Overview

The 800A1R5DT250X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX, part of the 800A series., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.

Technical Specifications

Part Number800A1R5DT250X
ManufacturerKYOCERA AVX
Series800A
Frequency RangeGHz / Microwave (Series Dependent)
Q FactorHigh Q (Series Dependent)
RF SuitableYES
High QYES
Low LossYES
ToleranceRefer to datasheet
Package / Case StyleRefer to datasheet
Dielectric MaterialRefer to datasheet
Temperature CoefficientRefer to datasheet
Operating Temperature RangeRefer to datasheet
Termination FinishRefer to datasheet
Mounting TypeSurface Mount (SMD/SMT)
RoHS ComplianceRoHS Compliant
REACH ComplianceREACH Compliant
Country of OriginUnited States
Manufacturer Part Number800A1R5DT250X
Data ConfidenceSeries Based
Verification NoteRequires ATC datasheet confirmation

Key Features

  • High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
  • Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
  • RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
  • Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
  • Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.

Applications

  • RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
  • Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
  • Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
  • Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
  • Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.

Compatible and Alternative Part Numbers

  • Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
  • Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the 800A product family
  • Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)

About KYOCERA AVX

KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.

About Superb Automation — Trusted KYOCERA AVX Supplier

Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.

Why Source 800A1R5DT250X from Superb Automation?

  1. Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
  2. Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
  3. Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
  4. Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
  5. One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
  6. Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
  7. Global Logistics — International shipping with full export documentation.

Ordering Information

To order 800A1R5DT250X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com

800A1R5DT250X: 1.5 pF at 250 V in the case A outline

Six decisions sit inside 800A1R5DT250X: series 800A, case A at 1.40 mm square, 1R5 is the capacitance code with the R holding the decimal place, so the printed value is 1.5 pF, tolerance D at plus or minus 0.50 pF, termination T for tin plated over a nickel barrier, the voltage field 250 for 250 VDC, and X for laser marking. The sheet runs 0.1 pF to 100 pF in this case at ratings up to 250 VDC, so on a 1.5 pF part the capacitance code and the voltage field are what separate it from the reel beside it in the store.

Series and case800A in case A, a 0.055 inch square outline, 1.40 mm by 1.40 mm overall
Capacitance1.5 pF, code 1R5
ToleranceD, plus or minus 0.50 pF, a window of 1.00 to 2.00 pF
Working voltage250 VDC, 177 V RMS on a sine wave
Dielectric withstanding625 V for five seconds, 250 percent of the working voltage
Life test500 V for 2000 hours at 125 degrees C, 200 percent of the working voltage
Temperature coefficientzero plus or minus 30 ppm per degree C, minus 55 to plus 125 C
Operating rangeminus 55 to plus 125 degrees C, no derating of working voltage
Quality factorgreater than 2,000 at 1 MHz, the figure the sheet prints for the series
Insulation resistance at 25 C10^5 Mohm minimum at the rated voltage
Insulation resistance at 125 C10^4 Mohm minimum at the rated voltage
Outline0.055 plus 0.015 minus 0.010 inch, 1.40 plus 0.38 minus 0.25 mm, 1.45 mm thick at most
Termination overlap0.010 plus 0.010 minus 0.005 inch, 0.25 plus 0.25 minus 0.13 mm
Terminal strength5 lbs minimum and 10 lbs typical for five seconds, perpendicular pull
Drift and retraceplus or minus 0.02 percent or 0.02 pF, whichever is greater
Aging and piezoelectric effectsnone stated for both on this sheet
Stored energy46.9 nanojoule at 250 V, from one half C V squared
Stored charge0.38 nanocoulomb at 250 V
Reactance at 150 MHz707.4 ohm nominal
Packingtape and reel 4000 or 500 pieces, vertical tape and reel on the same counts

Across 0.1 pF to 100 pF the case stays 1.40 mm square and the NP0 dielectric stays the same, while the ratings top out at 250 VDC. The 1.5 pF value on this page sits at 250 V with a D window, and those two fields are what goods in reads against the label.

Because 800A1R5DT250X stops at the marking field, the packing code is quoted with the order and nothing else is left loose. For 1.5 pF at 250 V the three fields read at goods in are the capacitance code 1R5, the tolerance letter D and the voltage field 250, and all three are printed inside the part number.

Case A body at 1.5 pF

Mechanically the 1.5 pF value at 250 V is a 1.40 mm square body no more than 1.45 mm thick, with 0.25 mm of overlap between termination and ceramic. Terminal strength is printed as 5 lbs minimum and 10 lbs typical for five seconds in a direction perpendicular to the termination surface, so a fixture that clamps the board for test has to stay under that pull.

Because the case is small, the pad row matters more than the tolerance letter for yield: the tight rows trade solder volume for placement room. On the 1.5 pF part at 250 V the drawing names the row and the stencil follows it, and the overlap stays 0.25 mm whichever row is used.

Electrical limits at 250 VDC

On 800A1R5DT250X the voltage story is a 250 V rating, a withstanding test at 625 V for five seconds, the same 250 percent for every value in the case, and a 2000 hour life test at 125 degrees C with 200 percent of the rating applied, which is 500 V on this part.

Receiving inspection on a 1.5 pF part at 250 V usually starts with drift and retrace, plus or minus 0.02 percent or 0.02 pF, whichever is greater. At this value the 0.02 pF floor governs: 30 ppm across 180 degrees comes to only 0.0081 pF, so the printed floor is what a tuned stage actually sees after a thermal cycle.

What 1.5 pF does from 30 MHz to 1 GHz

Read as reactance the 1.5 pF part at 250 V is 3537 ohm at 30 MHz, 707.4 ohm at 150 MHz, 212.2 ohm at 500 MHz and 106.1 ohm at 1 GHz, and against 50 ohm it does not reach 50 ohm anywhere inside the band, because the crossing sits at about 2.12 GHz. Below self resonance the body behaves as a capacitor and the figure falls with frequency, above it the same body turns inductive.

At 250 V the 1.5 pF value holds 707.4 ohm at 150 MHz and its loss budget is a quality factor above 2,000 at 1 MHz. Because no amperage is printed for this case, the current a 1.5 pF body can carry at 250 V is read from the supplier curve for the mounting, not from a number on the data sheet.

Temperature is the other half of the frequency picture. The coefficient is zero plus or minus 30 ppm per degree C, so a 1.5 pF part at 250 V moves by about 0.0081 pF over the full minus 55 to plus 125 degrees C range, which at 150 MHz is 3.820 ohm on top of the accepted window.

Used as a series coupling element into 50 ohm the 1.5 pF value turns over at 2.12 GHz, the point where its reactance equals the load resistance. On a 250 V rail that frequency decides whether the part works as a coupling capacitor or sits as a small series impedance, and it is read together with the 707.4 ohm it presents at 150 MHz.

Sourcing the 1.5 pF value and the second source

A 1.5 pF part at 250 V ships on tape and reel at 4000 or 500 pieces, in horizontal or vertical orientation, or in a tray or box, and the packing code is a line on the order rather than a field inside the part number. Component Lead Time Solutions, Pin to Pin Cross Reference, Kitting Service holds the sourcing path, and a second source is matched on capacitance, tolerance, voltage and case before a sample is released, because another case changes the pad and a wider tolerance changes the window.

For a 1.5 pF value rated at 250 V the order needs the capacitance code, the tolerance letter, the voltage field and a packing quantity, and nothing else changes the price of the package. Incoming inspection then reads the marking, measures against the D window and confirms the voltage field on the label.

Package and lot records travel with the 1.5 pF part at 250 V, because a value this small is hard to confirm on a meter that was not zeroed. The order records packing code, date code and quantity, and the incoming check is written against those fields so a later build traces back to the same lot.