Contact Us

116SCA1R0D100TT KYOCERA AVX RF Capacitor

Brand: ATC
The 116SCA1R0D100TT is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
quote now

Product Specifications

PRODUCT SPECIFICATIONS

116SCA1R0D100TT — KYOCERA AVX RF/Microwave Capacitor

Product Overview

The 116SCA1R0D100TT is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.

Technical Specifications

Part Number116SCA1R0D100TT
ManufacturerKYOCERA AVX
Frequency RangeGHz / Microwave (Series Dependent)
Q FactorHigh Q (Series Dependent)
RF SuitableYES
High QYES
Low LossYES
ToleranceRefer to datasheet
Package / Case StyleRefer to datasheet
Dielectric MaterialRefer to datasheet
Temperature CoefficientRefer to datasheet
Operating Temperature RangeRefer to datasheet
Termination FinishRefer to datasheet
Mounting TypeSurface Mount (SMD/SMT)
RoHS ComplianceRoHS Compliant
REACH ComplianceREACH Compliant
Country of OriginUnited States
Manufacturer Part Number116SCA1R0D100TT
Data ConfidenceSeries Based
Verification NoteRequires ATC datasheet confirmation

Key Features

  • High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
  • Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
  • RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
  • Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
  • Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.

Applications

  • RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
  • Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
  • Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
  • Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
  • Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.

Compatible and Alternative Part Numbers

  • Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
  • Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
  • Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)

About KYOCERA AVX

KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.

About Superb Automation — Trusted KYOCERA AVX Supplier

Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.

Why Source 116SCA1R0D100TT from Superb Automation?

  1. Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
  2. Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
  3. Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
  4. Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
  5. One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
  6. Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
  7. Global Logistics — International shipping with full export documentation.

Ordering Information

To order 116SCA1R0D100TT or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com

116SCA1R0D100TT: 1.0 pF single layer capacitor at 100 V

116SCA1R0D100TT unpacks into six decisions: 116 Series, case S, dielectric CA, 1R0 puts the R where the decimal point sits, so the value is 1.0 pF, tolerance D at plus or minus 0.5 pF, and 100 V with TT termination. A buyer who changes one letter has a different part on the same drawing, which is why the marking on the reel is read against the number and not against the label on the bag.

Series and outline116 Series Microcap, single layer, case S at 0.018 inch (0.457 mm)
DielectricCA, dielectric constant 60
Capacitance1.0 pF, code 1R0
ToleranceD, plus or minus 0.5 pF, a window of 0.500 to 1.500 pF
Rated voltage100 VDC, three digit voltage field
TerminationTT, titanium tungsten with nickel and gold, over 100 micro inch gold
Body thickness0.0045 to 0.012 inch (0.114 to 0.305 mm)
Dielectric capacitance range0.1 to 27 pF
Operating frequencyprinted up to 100 GHz for the single layer family
Insulation resistance1 x 10^11 ohm minimum at plus 25 degrees C at rated voltage
Dielectric test250 percent of rated voltage for 5 seconds
Environmental limitsbuilt to meet the limits of MIL-C-49464
Test methodsMIL-STD-202 methods 104, 106, 108, 208 and 210
Life test conditionplus 125 degrees C at twice rated voltage
Series resonanceprinted as a typical curve only, with no numeric table
Bond strengthMIL-STD-883 method 2019 die shear
Wire bondabilityMIL-STD-883 method 2011 and MIL-C-49464 paragraph 3.12
RoHScompliant, as for every product in this catalogue
Reactance at 1 GHz159.2 ohm nominal
Stored energy at 100 V5.0 nanojoule

For a 1.0 pF part the accepted band runs from 0.500 to 1.500 pF, and the letter D is what writes it. Incoming inspection measures against that window at the rated 100 V, and a substitution with the same nominal and a looser letter is the failure mode this page exists to prevent.

Spelled out, 116SCA1R0D100TT is a 116 Series single layer capacitor, case S at 0.018 inch (0.457 mm), dielectric CA, 1R0 puts the R where the decimal point sits, so the value is 1.0 pF, tolerance D at plus or minus 0.5 pF, rated 100 V, finished TT. Six fields, one part, and a change in any one of them is a different item on the same page of the catalogue.

Case S body, TT termination and assembly

The mechanical statement for 116SCA1R0D100TT is short: case S, 0.018 inch (0.457 mm) square, thickness between 0.0045 and 0.012 inch. Nothing there moves when the capacitance or the voltage field moves, which is why a like for like replacement on an existing board is possible at all, and why the case letter is quoted first on a second source request.

Termination TT carries a gold surface over nickel over titanium tungsten, and the sheet prints the thicknesses rather than a generic claim: over 100 micro inch gold, 1500 to 2000 angstrom nickel, 500 angstrom titanium tungsten. Die shear follows MIL-STD-883 method 2019 and wire bondability method 2011, so the same finish serves a soldered joint and a bonded wire.

Dielectric CA and the 100 V rating

CA is the coefficient of 116SCA1R0D100TT, printed as zero plus or minus 30 ppm per degree C over minus 55 to plus 125 degrees C, and 60 is its dielectric constant. Across that span a 1.0 pF body moves by about 0.0000 pF across the range, which is the figure a tuned stage sees on top of the plus or minus 0.5 pF window.

Read the material first: CA, constant 60, coefficient zero plus or minus 30 ppm per degree C from minus 55 to plus 125 degrees C. On the 1.0 pF value that comes to about 0.0000 pF across the range, and the tolerance D adds plus or minus 0.5 pF on top, so the two together bound what the circuit can expect.

The rating is 100 VDC, which is the top of the printed range for the whole single layer family, with a dielectric test at 250 percent of rating for 5 seconds and insulation resistance of 1 x 10^11 ohm minimum at plus 25 degrees C at rated voltage. Printed for this material: a capacitance range of 0.1 to 27 pF and a dissipation factor of 0.15 percent at 1 MHz.

What 1.0 pF does from 30 MHz to 2.45 GHz

Read as reactance the 1.0 pF part at 100 V is 5305 ohm at 30 MHz, 1061 ohm at 150 MHz, 318.3 ohm at 500 MHz, 159.2 ohm at 1 GHz and 65.0 ohm at 2.45 GHz, so into 50 ohm it does not reach 50 ohm anywhere inside the band, because the crossing sits at about 3.18 GHz. Those figures are computed at the nominal value and move in proportion with the tolerance letter, which is why the window and the reactance are quoted together.

One figure settles the application: into 50 ohm the 1.0 pF part reaches its half power point at 3.18 GHz. A 100 V stage that has to work below that point needs a larger value, and one that works above it can use this body as a coupling element with 1061 ohm left in the line at 150 MHz.

Loss is the one place where this catalogue stops short of a number. It prints a typical resonance curve against capacitance for minimum thickness and a typical loss curve for the family, and no single ohm or ampere figure for a 1.0 pF part, so the loss budget is read off the curve for the value and the mounting.

At 100 V the 1.0 pF body holds 5.0 nanojoule and 0.10 nanocoulomb. Both are small, and both are what a discharge path has to absorb if the part ever sits across a supply instead of in a signal line.

Sourcing the 1.0 pF value and the second source

Packing on the Quik Pick list is a 100 piece cap pac per value with 48 hour shipment quoted by the catalogue, and the custom kits are built from the same list, ten values by ten pieces for 100 pieces total. On a 1.0 pF part at 100 V that sets how many boards one pac covers. RF Component Sourcing, BOM Shortage Recovery, Incoming Inspection Plan holds the sourcing path, and a second source is matched on capacitance, tolerance, voltage, dielectric and case before a sample is released.

For a 1.0 pF value rated at 100 V the order needs five fields and one pac quantity, and nothing else on this page moves the price of a small order. Incoming inspection reads the marking, measures against the plus or minus 0.5 pF window from 0.500 to 1.500 pF, and confirms the voltage field on the label.

Package and lot records travel with the 1.0 pF part at 100 V, because a body this small is hard to confirm on a meter that was not zeroed. The order records the pac quantity, the date code and the reel or pac marking, and the incoming check is written against those fields so a later build traces back to the same lot.