100E512KW500X KYOCERA AVX RF Capacitor
Product Specifications
PRODUCT SPECIFICATIONS
100E512KW500X — KYOCERA AVX RF/Microwave Capacitor
Product Overview
The 100E512KW500X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
Technical Specifications
| Part Number | 100E512KW500X |
| Manufacturer | KYOCERA AVX |
| Frequency Range | GHz / Microwave (Series Dependent) |
| Q Factor | High Q (Series Dependent) |
| RF Suitable | YES |
| High Q | YES |
| Low Loss | YES |
| Tolerance | Refer to datasheet |
| Package / Case Style | Refer to datasheet |
| Dielectric Material | Refer to datasheet |
| Temperature Coefficient | Refer to datasheet |
| Operating Temperature Range | Refer to datasheet |
| Termination Finish | Refer to datasheet |
| Mounting Type | Surface Mount (SMD/SMT) |
| RoHS Compliance | RoHS Compliant |
| REACH Compliance | REACH Compliant |
| Country of Origin | United States |
| Manufacturer Part Number | 100E512KW500X |
| Data Confidence | Series Based |
| Verification Note | Requires ATC datasheet confirmation |
Key Features
- High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
- Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
- RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
- Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
- Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.
Applications
- RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
- Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
- Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
- Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
- Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.
Compatible and Alternative Part Numbers
- Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
- Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
- Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)
About KYOCERA AVX
KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.
About Superb Automation — Trusted KYOCERA AVX Supplier
Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.
Why Source 100E512KW500X from Superb Automation?
- Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
- Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
- Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
- Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
- One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
- Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
- Global Logistics — International shipping with full export documentation.
Ordering Information
To order 100E512KW500X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com
100E512KW500X: 5100 pF at 500 V in the case E body
Break 100E512KW500X into its fields and nothing is left to read from a headline. The series is 100, the case is E, the capacitance code 512 gives 5100 pF, the tolerance letter K gives plus or minus 10 percent, the termination letter W gives tin and lead solder plated over a nickel barrier, the voltage field is 500 VDC, and the X field is laser marking.
Case E is the 9.65 mm square porcelain body carrying 5100 pF with K tolerance at 500 V, 4.32 mm maximum thickness with a 1.02 mm maximum termination overlap. The dielectric is P90 porcelain at plus 90 plus or minus 30 ppm per degree C, the series is rated minus 55 to plus 125 degrees C with no derating of the working voltage, and quality factor is published as greater than 10,000 at 1 MHz from 1 pF to 1000 pF, and at 1 kHz above that range for a 5100 pF body. Marked at 5100 pF and 500 V, this code carries 2550 nanocoulomb at the rating.
The temperature coefficient is plus 90 plus or minus 30 ppm per degree C over minus 55 to plus 125 degrees C, so the 5100 pF value behind the 638 microjoule at 500 V drifts by parts per million rather than by percent across the rating of the K part. Packing is not carried in the code 100E512KW500X; the table gives tape and reel at 250 pieces or a tray of 24 or 96, and the count on the label has to match the count on the reel.
| Series and case | 100E, case E, 9.65 mm by 9.65 mm |
| Capacitance | 5100 pF, code 512 |
| Tolerance | K, plus or minus 10 percent, a window of 4590 to 5610 pF |
| Working voltage | 500 VDC, 354 V RMS at 0.707 times the DC rating |
| Dielectric withstanding | 1250 V for five seconds, 250 percent of the working voltage |
| Life test | 1000 V for 2000 hours at 125 degrees C, 200 percent of the working voltage |
| Temperature coefficient | plus 90 plus or minus 30 ppm per degree C |
| Operating range | minus 55 to plus 125 degrees C with no derating of the working voltage |
| Insulation resistance | 10^5 Mohm minimum at 25 degrees C and 10^4 Mohm minimum at 125 degrees C, both measured at 500 VDC |
| Leakage floor | 5 nA at 500 V and 50 nA at 125 degrees C, computed from those resistance floors |
| Stored energy | 638 microjoule at the working voltage, from one half C V squared |
| Stored charge | 2550 nanocoulomb at the working voltage |
| Reactance at 150 MHz | 0.21 ohm nominal |
| Reactance at 500 MHz | 0.06 ohm nominal |
| Series resonance | 55 MHz typical at this value, published in the 100 series table |
| ESR | 0.01 ohm at 30 MHz, 0.022 at 150 MHz |
| Quality factor | Greater than 10,000 at 1 MHz from 1 pF to 1000 pF, and at 1 kHz above that range |
| Termination | W, tin and lead solder plated over a nickel barrier, a lead bearing finish |
| Marking and packing | laser marking; tape and reel at 250 pieces, or a tray of 24 or 96 pieces |
| Mounting pad | A .405, B .050, C .325 and D .425 inch on the normal density pad, .385, .030, .325 and .385 on the high density one |
What 5100 pF does from 30 MHz to 1 GHz
At 30 MHz this 5100 pF body presents 1.04 ohm, at 150 MHz 0.21 ohm, at 500 MHz 0.06 ohm and at 1 GHz 0.03 ohm. Above a few hundred picofarads the 5100 pF part is a bypass and a DC block, so the useful question is how low the impedance stays at the top of the band, and 0.03 ohm at 1 GHz answers it better than the nominal capacitance does.
Tolerance is easier to judge in reactance than in picofarads. At 500 MHz the K window of 4590 to 5610 pF lands at 0.057 ohm at the top of the window and 0.069 ohm at the bottom, a spread of 0.013 ohm between the two ends against a 0.062 ohm nominal, which is 20.2 percent of that reactance. For a 5100 pF part at 500 MHz the 20.2 percent spread is the number to quote to the circuit owner, and the K letter follows from that number rather than from habit.
The series publishes 55 MHz of series resonance at the K pF code in 5100 tolerance, and that number carries about 1.6 nH of series inductance with it. Below 55 MHz the body is capacitive and the reactance falls with frequency; above it the same 5100 pF body in K tolerance is inductive and the reactance rises again, so the part is a short only in the window around its own resonance and a larger value is not automatically the better bypass.
Where a 5100 pF case E part is chosen
Chosen above a few hundred picofarads, the capacitor is the low impedance element in the circuit: the return path behind a radio frequency power stage, the shunt leg of a filter, the reservoir at a bias feed and the DC block into a load. At 500 MHz its 0.06 ohm is 0.1 percent of the line, and the question at this value is current and self heating rather than tolerance.
High frequency power amplifiers, transmitters, antenna tuning, plasma chambers and magnetic resonance coils are the circuits the series lists, and all of them put radio frequency current through the body at a working voltage that leaves little room: a 5100 pF part in K tolerance at 500 V carries 2550 nanocoulomb per half cycle, so the current is set by the frequency and not by the capacitance alone.
A 5100 pF part in K tolerance rated 500 V is tested at 1250 V for five seconds and at 1000 V for 2000 hours at 125 degrees C, 250 and 200 percent of the rating. The 5 nA and 50 nA leakage figures for this 5100 pF body follow from the insulation resistance floors and land as 50.0 mV on a 1 Mohm node at 125 degrees C.
Questions that arrive with a shortage quote
On a shortage, is a different tolerance letter a legal swap for the K code? The ceramic and the case do not change and the letter is a sort, so the question is only how much window the circuit absorbs. At 5100 pF the K window is 4590 to 5610 pF, the next grade tighter is J at plus or minus 5 percent, and the next grade looser is M at plus or minus 20 percent. At 500 MHz those ends land at 0.057 ohm at the top of the window and 0.069 ohm at the bottom, a spread of 0.013 ohm against a 0.062 ohm nominal, so a match or a filter has to hold the K letter while a bypass position does not care. The order for 100E512KW500X goes out with the tolerance letter we have confirmed, not the one that was asked for, and the shipping documents repeat it.
What proof comes with a K part? Three fields decide whether the lot is usable: a capacitance measurement at the frequency the series specifies, which for this value is 1 MHz, a withstanding record against 1250 V for five seconds, and the finish code, because W is tin and lead and a restricted build needs a deviation. The K letter has to be on the label as well, because a reel marked only with 5100 pF does not say whether the window is 4590 to 5610 pF or a wider one.
Can this K letter be ordered with a different finish? Yes, the finish is a field of its own: for a 5100 pF part in K tolerance W is tin and lead over nickel and is lead bearing, T is the RoHS compliant tin over nickel, P is a heavy tin and lead pellet, CA a gold chip, MS a microstrip style, and AR, AW and RW the leaded outlines. The body stays the same 5100 pF at 500 V, so the change is a compliance and mounting decision, and the packing still comes from the mechanical table at 250 pieces on tape and reel or 24 or 96 in a tray.
What to send with an enquiry
Four fields decide the price and the date: quantity, target date, the full order code 100E512KW500X with the tolerance and termination letters, and the packing the line accepts. Give us the complete code 100E512KW500X and the revision is checked before anything is priced, with date codes, packing and country of origin confirmed on the quotation itself. The Component Lead Time Solutions page sets out how a radio frequency bill is sourced and what a second source has to prove, the Pin to Pin Cross Reference page covers the route when a value is on allocation, and the Kitting Service page sets out the packing, kitting and inspection options a production line asks for.