Contact Us

100E512JW500X KYOCERA AVX RF Capacitor

Brand: ATC
The 100E512JW500X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
quote now

Product Specifications

PRODUCT SPECIFICATIONS

100E512JW500X — KYOCERA AVX RF/Microwave Capacitor

Product Overview

The 100E512JW500X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.

Technical Specifications

Part Number100E512JW500X
ManufacturerKYOCERA AVX
Frequency RangeGHz / Microwave (Series Dependent)
Q FactorHigh Q (Series Dependent)
RF SuitableYES
High QYES
Low LossYES
ToleranceRefer to datasheet
Package / Case StyleRefer to datasheet
Dielectric MaterialRefer to datasheet
Temperature CoefficientRefer to datasheet
Operating Temperature RangeRefer to datasheet
Termination FinishRefer to datasheet
Mounting TypeSurface Mount (SMD/SMT)
RoHS ComplianceRoHS Compliant
REACH ComplianceREACH Compliant
Country of OriginUnited States
Manufacturer Part Number100E512JW500X
Data ConfidenceSeries Based
Verification NoteRequires ATC datasheet confirmation

Key Features

  • High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
  • Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
  • RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
  • Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
  • Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.

Applications

  • RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
  • Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
  • Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
  • Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
  • Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.

Compatible and Alternative Part Numbers

  • Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
  • Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
  • Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)

About KYOCERA AVX

KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.

About Superb Automation — Trusted KYOCERA AVX Supplier

Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.

Why Source 100E512JW500X from Superb Automation?

  1. Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
  2. Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
  3. Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
  4. Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
  5. One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
  6. Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
  7. Global Logistics — International shipping with full export documentation.

Ordering Information

To order 100E512JW500X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com

100E512JW500X: 5100 pF at 500 V in the case E body

Read 100E512JW500X from the left and every character is a decision that has to match the drawing. 100 is the series, E is the case, 512 is the EIA capacitance code, so the marked value is 5100 pF, J sets the window at plus or minus 5 percent, W is the lead bearing tin and lead plate over a nickel barrier, 500 is the working voltage, and X is laser marking.

Case E is the 9.65 mm square porcelain body carrying 5100 pF with J tolerance at 500 V, 4.32 mm maximum thickness with a 1.02 mm maximum termination overlap, and that square is what buys the voltage: 638 microjoule at 500 V is the whole stored energy of the part, so the body is sized for the field across the porcelain rather than for the energy it holds.

P90 porcelain carries the temperature coefficient of plus 90 plus or minus 30 ppm per degree C across the whole minus 55 to plus 125 degrees C range, and the 638 microjoule held by the 5100 pF code in J tolerance at 500 V moves with the square of the voltage rather than with temperature. The string stops at laser marking, so packing is a separate field for 100E512JW500X: 250 pieces on tape and reel, or 24 or 96 in a tray, with the label count matching the box.

Series and case100E, case E, 9.65 mm by 9.65 mm
Capacitance5100 pF, code 512
ToleranceJ, plus or minus 5 percent, a window of 4845 to 5355 pF
Working voltage500 VDC, 354 V RMS at 0.707 times the DC rating
Dielectric withstanding1250 V for five seconds, 250 percent of the working voltage
Life test1000 V for 2000 hours at 125 degrees C, 200 percent of the working voltage
Temperature coefficientplus 90 plus or minus 30 ppm per degree C
Operating rangeminus 55 to plus 125 degrees C with no derating of the working voltage
Insulation resistance10^5 Mohm minimum at 25 degrees C and 10^4 Mohm minimum at 125 degrees C, both measured at 500 VDC
Leakage floor5 nA at 500 V and 50 nA at 125 degrees C, computed from those resistance floors
Stored energy638 microjoule at the working voltage, from one half C V squared
Stored charge2550 nanocoulomb at the working voltage
Reactance at 150 MHz0.21 ohm nominal
Reactance at 500 MHz0.06 ohm nominal
Series resonance55 MHz typical at this value, published in the 100 series table
ESR0.01 ohm at 30 MHz, 0.022 at 150 MHz
Quality factorGreater than 10,000 at 1 MHz from 1 pF to 1000 pF, and at 1 kHz above that range
TerminationW, tin and lead solder plated over a nickel barrier, a lead bearing finish
Marking and packinglaser marking; tape and reel at 250 pieces, or a tray of 24 or 96 pieces
Mounting padA .405, B .050, C .325 and D .425 inch on the normal density pad, .385, .030, .325 and .385 on the high density one

What 5100 pF does from 30 MHz to 1 GHz

At 30 MHz this 5100 pF body presents 1.04 ohm, at 150 MHz 0.21 ohm, at 500 MHz 0.06 ohm and at 1 GHz 0.03 ohm. Above a few hundred picofarads the 5100 pF part is a bypass and a DC block, so the useful question is how low the impedance stays at the top of the band, and 0.03 ohm at 1 GHz answers it better than the nominal capacitance does.

Tolerance is easier to judge in reactance than in picofarads. At 500 MHz the J window of 4845 to 5355 pF lands at 0.059 ohm at the top of the window and 0.066 ohm at the bottom, a spread of 0.006 ohm between the two ends against a 0.062 ohm nominal, which is 10 percent of that reactance. That 10 percent is why the J letter is written on the order for a 5100 pF part, and why the same value in a bypass role at 500 MHz can take a wider one.

The series publishes 55 MHz of series resonance at the J pF code in 5100 tolerance, and that number carries about 1.6 nH of series inductance with it. Below 55 MHz the body is capacitive and the reactance falls with frequency; above it the same 5100 pF body in J tolerance is inductive and the reactance rises again, so the part is a short only in the window around its own resonance and a larger value is not automatically the better bypass.

Where a 5100 pF case E part is chosen

At 5100 pF the part is bought for a return path rather than for a match: the bypass behind a power stage, the reservoir on a bias feed, the shunt leg of a low pass filter, and the DC block into a load. The reactance at 500 MHz is 0.06 ohm and at 1 GHz 0.03 ohm, so the useful part of the band is where that number stays under an ohm.

The applications the series is written for are radio frequency power amplifiers, transmitters, antenna tuning, plasma chambers and magnetic resonance coils, and a 5100 pF part in J tolerance at 500 V belongs to one of them. Each of those circuits loads the body with radio frequency current at 500 MHz, so the current chart and the 0.06 ohm of reactance matter more than the nominal value printed on the reel.

The voltage rules for this 5100 pF code in J tolerance at 500 V are a withstanding test at 1250 V for five seconds, 250 percent of the rating, and a life test at 1000 V for 2000 hours at 125 degrees C, 200 percent. Leakage computed from the 10^5 and 10^4 Mohm floors for the 5100 pF body in J tolerance is 5 nA at 25 degrees C and 50 nA at 125 degrees C, which is 50.0 mV across 1 Mohm at the hot end.

Questions that arrive with a shortage quote

If the J grade is on allocation, will another letter do? The ceramic and the case do not change and the letter is a sort, so the question is only how much window the circuit absorbs. At 5100 pF the J window is 4845 to 5355 pF, the next grade tighter is G at plus or minus 2 percent, and the next grade looser is K at plus or minus 10 percent. At 500 MHz those ends land at 0.059 ohm at the top of the window and 0.066 ohm at the bottom, a spread of 0.006 ohm against a 0.062 ohm nominal, so a match or a filter has to hold the J letter while a bypass position does not care. For 100E512JW500X the quotation names the grade we can actually ship rather than the one in the request, so the line never receives a window it did not ask for.

Which documents should travel with the 100E512JW500X reel? The lot and date code, a capacitance measurement at the series test frequency with the fixture stated, the withstanding result at 1250 V for five seconds, and a statement of the finish, because the W option is lead bearing. For a 5100 pF part with a J window the capacitance reading alone is not enough either, since 4845 to 5355 pF can both sit inside the drawing while one end is outside the circuit's window.

How much does the termination letter change? W is tin and lead solder plated over a nickel barrier and is lead bearing, and on a 5100 pF part in J tolerance the alternatives are T for the RoHS compliant tin over the same barrier, P for a heavy tin and lead pellet, CA is a gold chip, MS is a microstrip part with silver leads, and AR, AW and RW are the leaded outlines. On a 5100 pF 500 V body the letter changes the finish, the mounting style and the compliance statement, and it does not change the capacitance or the working voltage. Packing for a 5100 pF J reel follows the same mechanical table, tape and reel at 250 pieces or a tray of 24 or 96.

What to send with an enquiry

Four fields decide the price and the date: quantity, target date, the full order code 100E512JW500X with the tolerance and termination letters, and the packing the line accepts. With the full string for 100E512JW500X in hand we check the revision in force, then confirm date codes, packing and country of origin on the quotation. The RF Component Sourcing page sets out how a radio frequency bill is sourced and what a second source has to prove, the BOM Shortage Recovery page covers the route when a value is on allocation, and the Incoming Inspection Plan page sets out the packing, kitting and inspection options a production line asks for.