Contact Us

100E102MW1000X KYOCERA AVX RF Capacitor

Brand: ATC
The 100E102MW1000X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.
quote now

Product Specifications

PRODUCT SPECIFICATIONS

100E102MW1000X — KYOCERA AVX RF/Microwave Capacitor

Product Overview

The 100E102MW1000X is a RF/microwave ceramic capacitor manufactured by KYOCERA AVX., with high-Q, low-loss performance characteristics. Designed for ghz / microwave (series dependent) applications — suitable for rf matching / microwave / communication.

Technical Specifications

Part Number100E102MW1000X
ManufacturerKYOCERA AVX
Frequency RangeGHz / Microwave (Series Dependent)
Q FactorHigh Q (Series Dependent)
RF SuitableYES
High QYES
Low LossYES
ToleranceRefer to datasheet
Package / Case StyleRefer to datasheet
Dielectric MaterialRefer to datasheet
Temperature CoefficientRefer to datasheet
Operating Temperature RangeRefer to datasheet
Termination FinishRefer to datasheet
Mounting TypeSurface Mount (SMD/SMT)
RoHS ComplianceRoHS Compliant
REACH ComplianceREACH Compliant
Country of OriginUnited States
Manufacturer Part Number100E102MW1000X
Data ConfidenceSeries Based
Verification NoteRequires ATC datasheet confirmation

Key Features

  • High Q Factor — Excellent quality factor for low-loss RF performance at operating frequency.
  • Low ESR — Low Equivalent Series Resistance ensures minimal signal attenuation in RF paths.
  • RF/Microwave Optimized — Designed for ghz / microwave (series dependent) frequency range with stable capacitance and high self-resonant frequency.
  • Surface Mount Package — Compatible with standard SMT reflow soldering and automated PCB assembly.
  • Rugged Construction — KYOCERA AVX capacitors manufactured in certified facilities with consistent batch performance.

Applications

  • RF Matching — Impedance matching networks for RF power amplifiers in base stations, small cells, and repeaters.
  • Microwave — Microwave circuit applications including couplers, filters, and resonant structures.
  • Communication — Telecom equipment — 5G NR base stations, microwave backhaul, satellite communication systems.
  • Medical — Medical electronics — MRI systems, RF ablation equipment, medical telemetry devices.
  • Aerospace — Aerospace and defense — radar systems, electronic warfare, avionics, satellite payloads.

Compatible and Alternative Part Numbers

  • Equivalent Manufacturers: Passive Plus, Presidio Components, Johanson Technology, Knowles/Dielectric Labs, Murata, TDK
  • Same Series Alternatives: Other capacitance, voltage, tolerance, and package variants within the KYOCERA AVX product family
  • Cross-Reference Guidance: When substituting, verify capacitance value, voltage rating, tolerance, package dimensions, dielectric type, and RF performance (Q factor, ESR, SRF)

About KYOCERA AVX

KYOCERA AVX capacitors are manufactured in ISO 9001 certified facilities and widely specified in reference designs from Analog Devices, Texas Instruments, MACOM, Qorvo, Broadcom, and other leading RF semiconductor manufacturers. Key applications include 5G NR base stations, satellite communication, military radar, MRI medical imaging, and automotive radar systems.

About Superb Automation — Trusted KYOCERA AVX Supplier

Superb Automation is a trusted electronic components supplier. We provide 100% genuine KYOCERA AVX capacitors with full warranty, lot traceability, and competitive pricing. Our service includes component sourcing, PCB manufacturing, PCBA assembly, and global logistics with engineering support.

Why Source 100E102MW1000X from Superb Automation?

  1. Trusted Supplier — 100% genuine, factory-original KYOCERA AVX products with full warranty and lot traceability.
  2. Competitive Pricing — Volume discounts available. Prototype and sample quantities supported.
  3. Fast Quotation — RFQs processed within hours. In-stock items ship same/next business day.
  4. Engineering Support — FAE team assists with capacitor selection, S-parameter simulation, and cross-reference.
  5. One-Stop Solution — Capacitors + PCB + PCBA assembly from a single supplier.
  6. Quality Assurance — ESD-protected handling, visual inspection, electrical verification before shipment.
  7. Global Logistics — International shipping with full export documentation.

Ordering Information

To order 100E102MW1000X or any KYOCERA AVX capacitor, contact us with: Part Number, Quantity, Target Price, Delivery Destination, Required Date. Contact: Info@superb-tech.com | www.superb-tech.com

100E102MW1000X: 1000 pF at 1000 V in the case E body

Read 100E102MW1000X from the left and every character was fixed before the order went out. 100 is the porcelain high radio frequency power series, E is the case, 102 is the capacitance code where the first two digits are the significant figures and the third is the number of zeros, which makes this a 1000 pF part, M is the tolerance code at plus or minus 20 percent, W is tin and lead solder plated over a nickel barrier, 1000 is the working voltage in volts DC, and X is laser marking.

Case E is the 9.65 mm square porcelain body carrying 1000 pF with M tolerance at 1000 V, 4.32 mm maximum thickness with a 1.02 mm maximum termination overlap. At 1000 V this one stores 500 microjoule and holds 1000 nanocoulomb, so neither the energy nor the charge is large at this value and the working voltage is the field that decides the case.

The dielectric is P90 porcelain at plus 90 plus or minus 30 ppm per degree C and the operating range is minus 55 to plus 125 degrees C with no derating, a span over which this 1000 pF part in M tolerance holds 500 microjoule at 1000 V. No packaging letter sits in 100E102MW1000X, so the reel or the tray comes from the mechanical configuration table: tape and reel at 250 pieces, or a tray of 24 or 96 for the W finish.

Series and case100E, case E, 9.65 mm by 9.65 mm
Capacitance1000 pF, code 102
ToleranceM, plus or minus 20 percent, a window of 800 to 1200 pF
Working voltage1000 VDC, 707 V RMS at 0.707 times the DC rating
Dielectric withstanding1500 V for five seconds, 150 percent of the working voltage
Life test1200 V for 2000 hours at 125 degrees C, 120 percent of the working voltage
Temperature coefficientplus 90 plus or minus 30 ppm per degree C
Operating rangeminus 55 to plus 125 degrees C with no derating of the working voltage
Insulation resistance10^5 Mohm minimum at 25 degrees C and 10^4 Mohm minimum at 125 degrees C, both measured at 500 VDC
Leakage floor10 nA at 1000 V and 100 nA at 125 degrees C, computed from those resistance floors
Stored energy500 microjoule at the working voltage, from one half C V squared
Stored charge1000 nanocoulomb at the working voltage
Reactance at 150 MHz1.06 ohm nominal
Reactance at 500 MHz0.32 ohm nominal
Series resonance120 MHz typical at this value, published in the 100 series table
ESR0.018 ohm at 30 MHz, 0.04 at 150 MHz
Quality factorGreater than 10,000 at 1 MHz from 1 pF to 1000 pF, and at 1 kHz above that range
TerminationW, tin and lead solder plated over a nickel barrier, a lead bearing finish
Marking and packinglaser marking; tape and reel at 250 pieces, or a tray of 24 or 96 pieces
Mounting padA .405, B .050, C .325 and D .425 inch on the normal density pad, .385, .030, .325 and .385 on the high density one

What 1000 pF does from 30 MHz to 1 GHz

At 30 MHz this 1000 pF body presents 5.31 ohm, at 150 MHz 1.06 ohm, at 500 MHz 0.32 ohm and at 1 GHz 0.16 ohm. Above a few hundred picofarads the part is a bypass and a DC block, so the useful question is how low the impedance stays at the top of the band, and 0.16 ohm at 1 GHz answers it better than the nominal capacitance does.

Tolerance is easier to judge in reactance than in picofarads. At 500 MHz the M window of 800 to 1200 pF lands at 0.27 ohm at the top of the window and 0.4 ohm at the bottom, a spread of 0.13 ohm between the two ends against a 0.32 ohm nominal, which is 41.7 percent of that reactance. A 1000 pF part in a match or a filter has to hold the M letter, while the same part used as a bypass at 500 MHz does not notice a 41.7 percent spread.

The series publishes 120 MHz of series resonance at the M pF code in 1000 tolerance, and that number carries about 1.8 nH of series inductance with it. Below 120 MHz the body is capacitive and the reactance falls with frequency; above it the same 1000 pF body in M tolerance is inductive and the reactance rises again, so the part is a short only in the window around its own resonance and a larger value is not automatically the better bypass.

Where a 1000 pF case E part is chosen

Above a few hundred picofarads the part is a bypass and a DC block: the return path behind a power stage, the reservoir at the feed point of a bias line, the shunt leg of a low pass filter, and the coupling element into a load that has to stay at a low impedance across a band rather than at a point. At 500 MHz this one is 0.32 ohm, a small fraction of a 50 ohm line, so the match is already made at the low end of the band.

The circuit families the series names are high frequency and radio frequency power amplifiers, transmitters, antenna tuning, plasma chambers and magnetic resonance coils, and every one of them asks the same two questions of a 1000 pF part in M tolerance: how much current the body carries at the frequency of operation, and how far the value may drift before the stage notices.

At 1000 V the withstanding test is 1500 V for five seconds, 150 percent of the rating, and the 2000 hour life test at 125 degrees C runs at 1200 V, 120 percent. On this 1000 pF part in M tolerance the resistance floor of 10^5 Mohm at 25 degrees C puts 10 nA of leakage at the full rating and the 10^4 Mohm floor at 125 degrees C puts 100 nA there, so a 1 Mohm bias node sees 100 mV at the hot end.

Questions that arrive with a shortage quote

Can the M code be swapped for another grade on a shortage? The ceramic and the case do not change and the letter is a sort, so the question is only how much window the circuit absorbs. At 1000 pF the M window is 800 to 1200 pF, the next grade tighter is K at plus or minus 10 percent, and there is no looser grade in this list. At 500 MHz those ends land at 0.27 ohm at the top of the window and 0.4 ohm at the bottom, a spread of 0.13 ohm against a 0.32 ohm nominal, so a match or a filter has to hold the M letter while a bypass position does not care. On 100E102MW1000X we quote the letter on the order and state on the quotation the grade we can actually ship, so the two never get mixed on the line.

What has to be on the certificate? Four things that a broker line often leaves off: the date code and the lot, the measured capacitance with the test frequency stated, which is 1 MHz for this value, the withstanding result against the 1500 V level for five seconds, and the finish, because W is lead bearing and a restricted build cannot take it without a deviation. A 1000 pF part in M tolerance also has to carry its tolerance letter on the paperwork, since the value alone does not tell the line which window arrived.

Is the W finish the only option? No. On the 1000 pF body in M tolerance W is tin and lead solder plated over a nickel barrier and is lead bearing; T is the RoHS compliant tin over a nickel barrier on the same body, P is the heavy tin and lead pellet, CA is a gold chip, MS is a microstrip style with silver leads and AR, AW and RW are the leaded styles. The termination letter changes the mounting and the compliance statement, not the 1000 pF or the 1000 V, so a line that has been buying W and is asked to move to T is changing a finish rather than a capacitor. Packing on a 1000 pF order follows the same table: tape and reel at 250 pieces, or a tray of 24 or 96.

What to send with an enquiry

Four fields decide the price and the date: quantity, target date, the full order code 100E102MW1000X with the tolerance and termination letters, and the packing the line accepts. Send the whole string for 100E102MW1000X and we check it against the current revision, then confirm date codes, packing and country of origin on the quotation. The RF Component Sourcing page sets out how a radio frequency bill is sourced and what a second source has to prove, the Component Lead Time Solutions page covers the route when a value is on allocation, and the Kitting Service page sets out the packing, kitting and inspection options a production line asks for.