Contact Us

HMC996LP4E

Brand: Analog Devices
Analog Devices HMC996LP4E is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC996LP4E — Analog & Mixed-Signal ICs | Superb Automation

HMC996LP4E

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC996LP4E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC996LP4E: 22 dB of Gain Control From 5 to 12 GHz on a Negative Control Voltage

The HMC996LP4E is a GaAs pHEMT analog variable gain amplifier that also works as a driver. It covers 5 GHz to 12 GHz, delivers up to 18.5 dB of gain, and moves that gain over a 22 dB range with a single control voltage between -1 V and -4.5 V. Maximum gain sits at the most negative end of that range, which is the detail most board bring ups trip over: the control pin is not a 0 V to 5 V input and a CMOS digital to analog converter alone cannot drive it.

The control pin needs a negative source

A control range that runs from -1 V to -4.5 V means the driving circuit has to produce a negative voltage, or sit on a negative rail and be referred to it. Two arrangements work in practice. A small negative rail from a charge pump inverter plus a digital to analog converter referred to that rail gives the full range and a monotonic curve. A single positive converter with a level shifting amplifier also works but needs a rail below -4.5 V to guarantee the top of the range over temperature. Whichever is used, the control should be able to reach -4.5 V with margin, because that is where the 18 dB of gain lives.

Where the gain, noise and intercept land

ParameterValueNote
Frequency range5 GHz to 12 GHzGain falls to 13 dB minimum in the 8.5 to 12 GHz half
Gain at maximum18.5 dB typicalControl voltage at -4.5 V
Gain control range22 dB typical, 15 dB minimumOver the full control voltage span
Noise figure2 dB at maximum gainDegrades as the gain is reduced
Output intercept+34 dBm at maximum gainThird order, two tones
Output compression+22 dBm, +23 dBm in the lower halfFalls with gain, since the output stage is what compresses

The supply current quoted in two places

The first page of the data sheet says the part requires 170 mA from a +5 V supply. The specification table is written at a total supply current of 120 mA, with the control at -4.5 V and the gate bias adjusted between -2 V and 0 V to reach that current. Both statements are about the same part, but a power budget should use the larger figure, because the gate bias is a factory setting that a reworked board will not reproduce exactly. Sizing a 5 V regulator at 120 mA and then finding 170 mA in the prototype is a common way to spend a week.

Where to put the attenuation in a receive chain

Because the noise figure is specified at maximum gain and the intercept at maximum gain, and both degrade as the gain comes down, the part behaves like every other variable gain stage: best noise at the top, best linearity relative to the input at the bottom. In a receiver the first stage should run near maximum gain and the gain reduction should be placed later in the chain, where the signal is already above the noise floor. Used the other way round, the front end loses sensitivity exactly when the incoming signal is weak and the loop asks for more gain.

Selection and sourcing

Against a discrete amplifier plus a digital step attenuator, this part saves the attenuator, its control lines and the matching between them, at the cost of a negative control voltage. Against a fixed gain amplifier it saves nothing and costs a control loop. The amplifier cross reference page puts the variable gain family next to its fixed gain neighbours, the how to choose an RF amplifier page covers the gain and noise trade, and stock is listed under RF component sourcing.