Contact Us

HMC-AUH232-Die

Brand: Analog Devices
Analog Devices HMC-AUH232-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC-AUH232-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC-AUH232-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC-AUH232-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC-AUH232-Die: a 43 GHz modulator driver that puts 8 V peak to peak into 50 ohm

The HMC-AUH232-Die is a gallium arsenide HEMT distributed driver amplifier chip with single ended inputs and outputs, DC to 43 GHz of small signal bandwidth and a typical 3 dB bandwidth of 46 GHz. It delivers up to 8 V peak to peak while drawing 180 mA from a 5 V supply, which is what makes it a lithium niobate modulator driver rather than a general purpose gain block.

Published values

ParameterValue
Frequency rangeDC to 43 GHz, 46 GHz typical 3 dB bandwidth
Small signal gain12 dB typical
Output voltageup to 8 V peak to peak
Inputs and outputssingle ended
Supply5 V at 180 mA, 0.9 W
Bias controlsVGG1 sets bias current, VGG2 trims gain
Die size2.1 mm x 1.70 mm x 0.1 mm, under 3.6 square millimetres
External componentsbias tee, dc blocking, supply bypass

What 8 V peak to peak means in current

Eight volts peak to peak into a 50 ohm load is 160 mA peak to peak, or 80 mA peak. The 180 mA supply current is what makes that possible with headroom, and it is also why the part dissipates 0.9 W rather than the few hundred milliwatts a small signal amplifier of the same gain would need.

The load in a real transmitter is not 50 ohm. A lithium niobate modulator presents a capacitive load with a termination, and the driver sees that termination through the interconnect. The 8 V figure is a voltage into the specified load, so a module with a different termination has to be measured rather than calculated from the datasheet.

Why the bias tee is external

The output carries dc, so the bias has to be injected through a tee and the load has to be blocked. That is stated as a requirement rather than as an option, and it is the component that most often limits the bandwidth of a module built with this die, because a bias tee with a low corner and a high self resonance is not a standard part.

The second bias pin, VGG2, trims gain. That gives a module a way to equalise the response without an attenuator, at the cost of a control voltage that has to be set per unit. For a production programme the trim is a calibration step, and it has to be in the test plan.

Group delay and phase, which the datasheet does not lead with

A modulator driver in a coherent optical link adds delay, and what matters is the variation of that delay across the band rather than its absolute value. The datasheet states that gain and phase ripple are good to 40 GHz, which is the qualitative version of the same claim.

For a 40 Gb/s link the signal occupies tens of gigahertz, and a delay variation of a few picoseconds across that band is a significant fraction of a bit period. Any module using this die should be measured for group delay with the actual interconnect, because the die is not the only contributor.

Applications

40 Gb/s lithium niobate and Mach-Zehnder modulators, broadband gain blocks for test equipment, broadband radio frequency gain blocks and military and space equipment. In the optical case the driver is in the transmit chain and its output swing sets the extinction ratio of the modulator.

In the test equipment case the same die is used as a general wideband amplifier, and the 8 V swing is not needed. That is fine, but it means the part is being bought for bandwidth rather than for swing, and a smaller die with less current would dissipate less.

Sourcing notes for this family: the amplifier cross reference holds the cross references, defense grade components is the pre substitution check, and vendor consolidation is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can the HMC-AUH232-Die drive a 50 ohm load directly? It can deliver up to 8 V peak to peak, which is 160 mA peak to peak into 50 ohm, within its 180 mA supply current. The bias tee and the dc blocking are external and are required.

What is the difference between VGG1 and VGG2? VGG1 sets the bias current of the device and VGG2 provides a limited gain adjustment. Both have to be set for the module, and both need to be sequenced with the drain supply.