ADMV7810
Product Specifications
ADMV7810
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADMV7810 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADMV7810: 81 GHz to 86 GHz, 29 dBm, and 18 percent efficiency
The ADMV7810 is a gallium arsenide pHEMT medium power amplifier die for the 81 GHz to 86 GHz band, with 20 dB of gain, 28 dBm at one decibel compression, 29 dBm saturated, 33 dBm of output third order intercept and an on chip temperature compensated detector, from 4 V at 800 mA. The die is 2.999 mm by 3.799 mm by 0.05 mm. It is the upper E band companion to the 71 GHz to 76 GHz part, and the four decibels of gain it gives up are the price of the higher frequency.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 81 GHz to 86 GHz |
| Gain | 20 dB typical |
| Output power at one decibel compression | 28 dBm typical |
| Saturated output power | 29 dBm typical |
| Output third order intercept | 33 dBm typical |
| Input return loss | 12 dB typical |
| Output return loss | 20 dB typical |
| Supply | 4 V at 800 mA |
| Power added efficiency | 18 percent, about 1.09 A of drain current at saturation |
| Die size | 2.999 mm by 3.799 mm by 0.05 mm |
Eighteen percent efficiency is 4.4 W of DC input
At 29 dBm the output is 0.79 W, and 18 percent efficiency means 4.36 W of DC input, which at 4 V is 1.09 A. The quiescent figure of 800 mA is lower than that, so the supply has to be sized for the operating current, not the idle current. On a 4 V rail, the difference between 0.8 A and 1.09 A is a quarter of an amp that has to come from somewhere during every transmission.
The remaining 3.6 W is heat inside a die of 11.4 square millimetres at 0.05 mm thickness. The thermal path is the same as the lower band part: through the attach and the carrier, with the die bottom as the return for the source. At 86 GHz the same attach that is electrically acceptable for the ground return is also the thermal path, so there is no separate answer for the two.
The match is reversed compared with the lower band part
This part publishes 12 dB of input return loss and 20 dB of output return loss, the opposite of its lower band companion, which gives 18 dB in and 10 dB out. Neither is better in the abstract; the two dice were matched differently for the components they are expected to drive. A system that swaps one for the other without rechecking the interfaces will find the mismatch in a different place.
Twelve decibels of input return loss is a 1.7 voltage standing wave ratio, which means the driver sees a load that moves with frequency. If the driver is a variable gain stage with its own output match, the interaction can produce a few tenths of a decibel of ripple that is not in either data sheet. The cure is a fixed pad or an attenuator between the two, chosen once the band is fixed.
Detector, bias and the assembly sequence
The detector is temperature compensated and follows the envelope, which is what a level loop in a backhaul radio needs. At 86 GHz the pad to sampling trace is short enough that the detector is usable without a coupler, and that is a meaningful saving in a radio where every millimetre of waveguide costs loss.
The bias is 4 V on the drain with a gate adjusted to set 800 mA, and the sequence has to bring the gate up first. On a die this is the carrier's job rather than the package's, so the bias circuit and its decoupling are part of the assembly job, not a board level afterthought. The 0.05 mm thickness also means the die cannot be probed or handled like a 0.1 mm part.
For a board that has to keep running while a reel runs out, the RF component sourcing page is where the family alternatives sit, component lead time solutions is the check list before a substitute goes in, and one stop RF supply is how a gap is covered without a new line item.
Two questions buyers ask
What is the difference between this and the 71 GHz to 76 GHz part? Band and gain. This one covers 81 GHz to 86 GHz with 20 dB of gain, the lower band part covers 71 GHz to 76 GHz with 24 dB, and both deliver 29 dBm saturated.
Do the input and output need matching on the carrier? No. Both are matched to 50 ohm on die. The bond wire length at input and output is the element that shifts the match, and it has to be kept short.