ADM3251EARWZ
Product Specifications
ADM3251EARWZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM3251EARWZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADM3251EARWZ: isolated RS-232 with the isolated supply included
The ADM3251EARWZ is a single channel RS-232 transceiver in a 20-lead wide body SOIC with 2.5 kV of isolation on both the data and the power path. The isoPower stage generates the isolated rail that the RS-232 side needs, so a port that has to be floating needs one package and four capacitors rather than a transceiver, a converter and a transformer.
Published values
| Parameter | Value |
|---|---|
| Function | fully isolated RS-232 transceiver, data and power |
| Isolation test voltage | 2500 V rms for one minute |
| Working voltage | 547 V peak |
| Data rate | 460 kbps |
| ESD on RS-232 pins | 8 kV contact, 15 kV air gap |
| Supply | single 5 V |
| Supply current | 2.0 mA typ, 2.4 mA max at 5.5 V, no load |
| Standards | IEC/CSA 61010-1 |
| Package and range | 20-lead wide body SOIC, -40 C to +85 C |
Why an isolated serial port is a power question
An RS-232 port that leaves a chassis has to survive a ground potential difference between the equipment and whatever is plugged into it. Isolating the data lines alone does not solve that, because the RS-232 side still needs a supply, and a supply that comes from the local ground re-establishes the connection the barrier was meant to break.
This part answers that by transferring power across the same barrier as the data. The 2.4 mA maximum input current at no load is the quiescent figure for the whole isolated port, which is small enough that a USB-powered instrument can carry one without a change to its supply budget.
547 V of working voltage in a 20-lead body
The 2500 V rms test rating is a one minute stress; 547 V peak is the continuous working voltage, which is 387 V rms. That covers a 230 V mains referenced instrument with the usual margin and it does not cover a 400 V drive, where a part with a higher working voltage is needed.
The IEC/CSA 61010-1 reference in the specification is the standard for measurement, control and laboratory equipment, which is where a floating serial port usually appears. A buyer checking a safety file should look for that standard rather than for the test voltage alone.
460 kbps and the isolated path
The data rate is the same as the non isolated 3.3 V part, because the barrier is fast enough not to be the limit at this speed. What changes is the propagation delay through the barrier, which has to be included in any protocol timing that assumes a direct connection.
The RS-232 side needs four 0.1 uF capacitors, the same charge pump arrangement as the non isolated part, and those capacitors sit on the isolated side. Their return path is the isolated ground, not the board ground, and mixing the two is the most common way an isolated port stops being isolated.
Replacement checks
A candidate has to match the isolation of both the data and the power path. A transceiver with an isolated data path and an external converter is a valid alternative, and it is a larger board with its own certification work. The single package is a schedule decision as much as an electrical one.
The pages below hold the family alternatives, the medical approvals route and the acceptance sequence.
When an order code in this family cannot be found, the ADI second source page lists what else does the same job, medical device components covers what to check before a part is dropped into an existing board, and how to verify a drop in replacement is the route we take on a live shortage.
Two questions buyers ask
Does the ADM3251EARWZ need an external isolated DC-DC? No. The isolated supply is generated inside the package, which is why the part is specified as fully isolated for both data and power.
What supply does it run from? A single 5 V rail on the logic side. The RS-232 levels and the isolated rail are generated internally.