ADG1612BCPZ
Product Specifications
ADG1612BCPZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1612BCPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1612BCPZ: four SPST switches at 1 ohm typical in a 4 mm LFCSP
The ADG1612BCPZ is the quad single pole single throw of the ADG1611/ADG1612/ADG1613 family, in the 4 mm by 4 mm LFCSP. On resistance is 1 ohm typical with 0.2 ohm flatness, the supply range is 3.3 V to 16 V single or 3.3 V to 8 V dual, continuous current is 280 mA per channel in the LFCSP and 175 mA in the TSSOP, and the switch closes on a logic high.
Published values
| Parameter | Value |
|---|---|
| Configuration | four SPST switches, closed on logic 1 |
| On resistance | 1 ohm typical |
| Flatness | 0.2 ohm |
| Continuous current | 280 mA per channel in LFCSP, 175 mA in TSSOP |
| Supply | 3.3 V to 16 V single, 3.3 V to 8 V dual |
| Logic | 3 V compatible, no VL supply required |
| Package | 4 mm x 4 mm LFCSP, 16 terminals |
One ohm changes which circuits are possible
At 1 ohm the switch can sit in series with a 50 ohm signal path and cost 2 percent, or in series with a 200 ohm load and cost half a percent. At 280 mA the drop is 0.28 V and the dissipation is 78 mW, so the part can switch a modest load and still be thermally comfortable, which is not true of the higher resistance members of the family at the same current.
Flatness of 0.2 ohm over the full signal range is the distortion term. On a 200 ohm load it is 0.1 percent, which is below the tolerance of the resistors around it, so an audio or instrumentation path through this switch is limited by the amplifier and not by the switch.
The logic polarity is part of the part number
The ADG1611 and the ADG1612 are the same switch with inverted control logic: the ADG1611 closes on logic 0, the ADG1612 closes on logic 1, and the ADG1613 mixes the two polarities in one package. Firmware written for one order code drives the other one inverted, and the mistake is silent because the part still switches, just at the wrong times.
On a board that is powered up before the microcontroller is out of reset, the control pins float. A pull resistor per control input is the only way to guarantee the state, and the polarity of the fitted order code decides which resistor goes to which rail.
Package and thermal notes
The 280 mA rating belongs to the LFCSP and the 175 mA rating to the TSSOP, which is a thermal difference rather than a silicon one. The exposed pad on the LFCSP is the path for that extra current, so the pad has to be soldered to a copper area, not left under a soldermask island.
On a 16 V single supply the analog range is 0 V to 16 V, and a signal that swings below ground needs a dual supply. The supply pins need decoupling rated for the full rail, and the analog pins need a clamp if the source can be live while the switch is unpowered.
Where it fits
Four channel routing in instrumentation, audio paths that need a low resistance switch, battery powered equipment with a 3.3 V to 16 V rail, and any board that has to switch a load of a few hundred milliamps without a relay.
Two pages worth reading before a purchase order goes out are how to verify a drop in replacement and the pin to pin cross reference; the first lists what else fits the socket, the second is the test sequence for a drop in, and component obsolescence management covers the case where the shortage is already on the line.
Two questions buyers ask
Is the ADG1612 a drop in for the ADG1611? The pins match but the control logic is inverted. Fitting an ADG1612 where an ADG1611 was specified turns every channel on when it should be off, which is a functional fault that a continuity test will not catch without the truth table.
Can it switch a signal below ground on a single supply? No. On a single rail the analog range is 0 V to VDD. A bipolar signal needs the dual supply configuration, and the dual range is 3.3 V to 8 V, so plus or minus 5 V is inside it and plus or minus 12 V is not.