Contact Us

AD8541ARTZ

Brand: Analog Devices
Analog Devices AD8541ARTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8541ARTZ — Analog & Mixed-Signal ICs | Superb Automation

AD8541ARTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8541ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8541ARTZ: single 45 microamp rail-to-rail amplifier in SOT-23-5

The AD8541ARTZ is a single CMOS rail-to-rail input and output amplifier in a 5-lead SOT-23 body, drawing 45 uA of supply current and delivering 1 MHz of gain bandwidth with a 6 mV maximum offset. It is the part that fits when a signal needs a buffer and the budget allows a few tens of microamps, not when the signal needs to be measured to a fraction of a millivolt.

Published values

ParameterValue
Offset voltage1 mV typical, 6 mV maximum
Offset voltage drift4 uV/C typical
Input bias current4 pA typical, 60 pA maximum
Supply current per amplifier45 uA typical, 65 uA maximum at 5 V
Gain bandwidth1 MHz at 5 V supply
Slew rate0.45 V/us typical, 0.92 V/us at 5 V
Voltage noise density42 nV/root Hz at 1 kHz
Output swing at 1 mA4.9 V minimum high, 25 mV typical low at 5 V supply
PSRR65 dB minimum, 76 dB typical
Settling to 0.1%6 us on a 1 V step
Phase margin67 degrees
Supply range2.7 V to 5.5 V single supply

What 6 mV of offset costs a converter

Six millivolts against a 5 V full scale is 0.12 percent, which is one part in 833, or about 9.7 bits. A 10-bit converter therefore sees the amplifier offset as less than one code and the part disappears into the error budget. A 12-bit converter has a 1.2 mV code, so the untrimmed offset is five codes and has to be removed in firmware or with a chopper part. A 16-bit converter cannot use this amplifier at DC without a calibration step, whatever the drift figure says.

The drift line is 4 uV/C typical with no maximum published, which matters more than the offset for a product that ships without calibration: 40 C of internal rise moves the offset by 160 uV typical, and there is no guaranteed ceiling on that number.

Why the input range beats the offset in most sockets

The input stage works from 0 V to the positive rail and the output swings to within 100 mV of the low rail and 100 mV of the high rail at 1 mA, so a single 3.3 V rail can carry a sensor signal that sits at ground without a charge pump. That, plus the 4 pA typical bias current, is the reason this family is used on photodiode and pH electrode inputs where the source impedance is high enough that a bipolar input would be the larger error term.

Stability with a capacitive load

67 degrees of phase margin at unity gain leaves room for about 100 pF of load before the loop starts to ring, which covers a short trace and a small filter capacitor but not a 1 nF cable. Put a 100 Ohm series resistor between the output and a cable, and keep the feedback taken from the amplifier side of that resistor, otherwise the added pole is inside the loop.

Where the part belongs

Reference buffers, ADC input buffers on 10-bit channels, comparator thresholds, low side current monitors and active filters below 100 kHz are the natural sockets. Anything that needs a guaranteed offset over temperature, or more than 100 kHz of signal bandwidth, belongs to another family, and the cross reference page lists the ones that fit the same footprint.

Sourcing notes for this family: the pin to pin cross reference holds the cross references, the amplifier cross reference is the pre substitution check, and how to reduce component cost is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can the AD8541ARTZ replace a bipolar op amp in an existing socket? Only after the input range is checked. This part takes its input to both rails, which a bipolar input cannot do, but the offset of 6 mV maximum is larger than the 1 mV class parts it would displace, and the 1 MHz bandwidth will change the loop.

Does it need an output capacitor? No. The part is unity gain stable without one, and adding a large capacitor directly on the output is the usual way to make it ring. Use a series resistor if a cable has to be driven.