Contact Us

AD8061ARTZ

Brand: Analog Devices
Analog Devices AD8061ARTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8061ARTZ — Analog & Mixed-Signal ICs | Superb Automation

AD8061ARTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8061ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8061ARTZ: 300 MHz in a Five Lead SOT-23 at 6.8 mA

The AD8061ARTZ is a rail to rail output voltage feedback amplifier in a 5-lead SOT-23 with 300 MHz of bandwidth at a gain of plus one and a 650 V per microsecond slew rate, which is the kind of speed normally associated with current feedback parts. Voltage noise is 8.5 nV per root hertz on a 5 V supply, settling to 0.1 percent on a 1 V step takes 35 ns, overload recovery takes 35 ns, and the quiescent current is 6.8 mA. Offset is 6 mV, the supply range is 2.7 V to 8 V, and the input common mode range on a 5 V supply is minus 0.2 V to 3.2 V. Into a 150 ohm load at a gain of two the differential gain error is 0.01 percent and the differential phase is 0.04 degrees, with gain flatness of 0.1 dB to 30 MHz.

Published values

ParameterValue
Bandwidth300 MHz at a gain of plus one
Slew rate650 V per microsecond
Settling time35 ns to 0.1 percent on a 1 V step
Overload recovery35 ns
Voltage noise8.5 nV per root hertz at 5 V
Offset voltage6 mV
Quiescent current6.8 mA per amplifier
Supply range2.7 V to 8 V
Input range on 5 VMinus 0.2 V to 3.2 V
Video0.1 dB flat to 30 MHz, 0.01 percent and 0.04 degree
Body5-lead SOT-23
FamilyAD8062 dual and AD8063 with a disable pin

Six millivolts of offset is ten codes

Six millivolts of offset on a 2.5 V range is 9.8 codes of a 12 bit converter and 157 codes of a 16 bit one, so this is not a direct current precision part despite the 300 MHz. It is an alternating current part: video, a photodiode preamplifier's second stage, a clock buffer, a filter. In those uses the offset is removed by a coupling capacitor or by a servo loop, and the 35 ns settling and the 8.5 nV noise are what matter. A board that needs both speed and direct current accuracy has to add a chopper or an auto-zero stage in front, and that stage's bandwidth then becomes the limit.

Three hundred megahertz and 650 volts per microsecond

The slew rate supports 345 mV peak at 300 MHz, so the headline bandwidth is a small signal figure and the full power bandwidth at 2 V peak to peak is about 50 MHz. In a video path at 4.43 MHz the part is far inside its limits and the 0.1 dB flatness to 30 MHz is what keeps the chroma and the luma aligned. In a clock buffer at 100 MHz with a 1 V swing the slew rate is the limiting number and the output looks like a trapezoid rather than a square, which is acceptable in a clock distribution tree and not acceptable in a fast comparator input.

Input range that stops 1.8 V below the positive rail

On a 5 V supply the input common mode is specified from minus 0.2 V to 3.2 V, so a signal biased at 2.5 V has 0.7 V of headroom upward and a signal that swings to 4.5 V is outside the range. This is the input stage limit of a rail to rail output part, and it is the single specification most often missed when a 3.3 V circuit is moved to 5 V: the bias point moves with the supply and the top of the signal leaves the input range. The output, by contrast, swings to the rails, so the part can drive a converter's full range even though it cannot sense that range.

The SOT-23 body and its feedback path

The five lead body has no ground pin between input and output, so the input node and the output node are adjacent on the package, and at 300 MHz the couple of picofarads between them is enough to matter. The feedback resistor should be short and should not run under the package, and the input trace should be guarded by the ground plane on the other side of the board. For a photodiode preamplifier, where the input node is high impedance, this is the difference between a stable stage and an oscillator, and the 6-lead version with a disable pin gives one more pin to separate the nodes. The amplifier cross reference page groups the high speed rail to rail parts by body and bandwidth, the pin to pin cross reference page lists the five and six lead footprints, and the obsolete part cross reference hub covers grades that are no longer catalog items.