AD8041ARZ
Product Specifications
AD8041ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8041ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8041ARZ: A Single 160 MHz Amplifier That Swings to the Rails
The AD8041ARZ is the single amplifier in a family whose dual is the AD8042 and whose quad is the AD8044, specified at 160 MHz of bandwidth at a gain of plus one, 200 V per microsecond of slew rate and 39 ns of settling to 0.1 percent. The output swings to within 30 mV of either rail, the input common mode extends 200 mV below ground and to within 1 V of the positive rail, and the part does not phase reverse with inputs 0.5 V beyond the supplies. Quiescent current is 5.2 mA per amplifier, the output drives 50 mA while staying 0.5 V from the rails, and gain flatness is 0.1 dB to 14 MHz with 0.02 percent differential gain and 0.04 degree differential phase into a 150 ohm load at a gain of two. Worst harmonic distortion at 10 MHz is minus 64 dBc.
Published values
| Parameter | Value |
|---|---|
| Bandwidth | 160 MHz at a gain of plus one |
| Slew rate | 200 V per microsecond |
| Settling time | 39 ns to 0.1 percent |
| Output swing | Within 30 mV of either rail |
| Input range | 200 mV below ground, within 1 V of the positive rail |
| Output current | 50 mA, 0.5 V from the rails |
| Quiescent current | 5.2 mA |
| Video | 0.1 dB flat to 14 MHz, 0.02 percent and 0.04 degree |
| Distortion | Minus 64 dBc worst harmonic at 10 MHz |
| Supply | Plus 3 V, plus 5 V and plus and minus 5 V specified |
| Body | 8-lead SOIC and 8-lead PDIP |
Asymmetric input range and what it means for a single supply
The input range reaches 200 mV below ground but stops 1 V short of the positive rail, which is the opposite of what a rail to rail input label suggests. On a 5 V single supply the usable common mode is then minus 0.2 V to 4 V, and a signal biased at 2.5 V has 1.5 V of headroom upward. That is why this part appears in mid supply biased single supply systems rather than in circuits that need to measure at the top rail. The output, on the other hand, swings to within 30 mV of both rails, so the limitation is at the input rather than at the output, and it is the input that decides whether a direct coupled sensor can be connected.
Two hundred volts per microsecond and 160 MHz
The slew rate supports a 199 mV peak sine at 160 MHz, so the 160 MHz figure is a small signal number, and at 2 V peak to peak the full power bandwidth is about 16 MHz. In a video path running at 5 MHz with a 2 V peak to peak signal, the part is well inside its slew limit and the 0.1 dB flatness to 14 MHz is the number that decides the picture quality. In a converter driver at 20 MHz the same part is at its limit and distortion rises, which is where the minus 64 dBc harmonic figure at 10 MHz becomes relevant.
Fifty milliamps and the video distribution case
Fifty milliamps of output current, quoted with the output 0.5 V from the rails, is enough to drive two back terminated 75 ohm video loads or a single 50 ohm cable at 2.5 V peak. Beyond that the output stage runs out of current before it runs out of voltage, and the distortion rises faster than the amplitude, which shows in a picture as a compression of the bright areas. A distribution amplifier driving four cables needs either a part with more current or one amplifier per output, and the second option is usually cheaper because the AD8042 dual puts two channels in one package for the same 5.2 mA per amplifier.
When a single is the right choice
The single version is specified at 3 V, 5 V and plus and minus 5 V, so it fits a 3.3 V system as well as a plus and minus 5 V analog section, and its pinout is the conventional single amplifier arrangement. In a board where only one channel needs this bandwidth, a single avoids the supply coupling of a dual and the wasted current of an unused half. Where two or four channels are needed, the dual and the quad share the same core and the same settling, so the choice is a package decision rather than an electrical one. The amplifier cross reference page groups the single high speed parts by supply and drive, the pin to pin cross reference page lists the bodies that swap, and the component lead time solutions page shows the availability position.