AD623ARZ
Product Specifications
AD623ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD623ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD623ARZ: The In-Amp That Works 150 mV Below Its Own Ground
The AD623ARZ is a rail to rail output instrumentation amplifier that runs from a single supply and accepts inputs 150 mV below ground. That one line explains most of its use: a thermocouple or a shunt sitting at the negative rail still has bias headroom, so a single supply build does not need a negative rail just to keep the input stage inside its window. Gain is set by one resistor with G equals 1 plus 100 k divided by RG, from 1 with no resistor fitted to 1000. Gain error is 0.10 percent at unity gain and 0.35 percent above it, input referred noise is 35 nV per root hertz at 1 kHz, and the bandwidth at unity gain is 800 kHz. The 8-lead body follows the industry standard pinout, so the footprint is interchangeable with other parts in this class.
Published values
| Parameter | Value |
|---|---|
| Gain equation | G equals 1 plus 100 k divided by RG |
| Gain range | 1 to 1000 |
| Output swing | Rail to rail |
| Input range | Extends 150 mV below ground on a single supply |
| Gain error | 0.10 percent at G equals 1, 0.35 percent above G equals 1 |
| Input noise | 35 nV per root hertz at 1 kHz |
| Bandwidth | 800 kHz at unity gain |
| Supply range | 3 V to 12 V specified, single or dual supplies |
| Common mode rejection | Constant to 200 Hz, improves with gain |
| Body | 8-lead surface mount, R suffix |
| Pinout | Industry standard 8-lead in-amp pinout |
Single supply is a bias question before it is a swing question
An instrumentation amplifier on a single 5 V rail has to hold its inputs inside a window that does not include the rails, and the usual failure is a sensor that sits at ground. The 150 mV below ground figure is what allows a shunt or a bridge return to sit at zero and still leave the input stage linear, and it is the difference between a working single supply channel and a rail to rail op amp pair with a charge pump in front of it. The rail to rail output then lets the full converter range be used without losing 0.6 V at each end. Taken together the part removes two of the three reasons people add a negative rail to a sensor front end.
Constant common mode rejection up to 200 Hz
Most in-amps lose common mode rejection as frequency rises, which matters when the interference is line frequency. The data sheet states that common mode rejection stays constant to 200 Hz, so 50 Hz and 60 Hz pickup are rejected by the same amount as dc offset. For a channel measuring a low level signal next to a transformer or a motor drive, that is worth more than a better dc figure, because the interfering signal is the one at line frequency and its harmonics.
Choosing between the AD623 and its low power siblings
The upgrade table in the data sheet lists parts with lower quiescent current, from about 30 microamps upward, and the trade is noise and bandwidth rather than accuracy. A battery powered 4 to 20 mA loop device wants the lowest quiescent current that still meets its noise budget, while a mains powered instrument can take the wider bandwidth. Body and pinout are shared across much of the family, which makes the choice a line item change in most cases. The amplifier cross reference lists the rail to rail in-amp families we supply, the pin to pin cross reference covers which of them share this footprint, and the ADI second source page covers grade equivalence.