Contact Us

AD1580ARTZ

Brand: Analog Devices
Analog Devices AD1580ARTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD1580ARTZ — Analog & Mixed-Signal ICs | Superb Automation

AD1580ARTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD1580ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD1580ARTZ: A 1.2 V Shunt Reference That Runs on 50 uA

The AD1580ARTZ is the A grade of a 1.2 V shunt voltage reference in a SOT-23 body. A shunt reference has no supply pin of its own: it regulates by drawing current through an external resistor, and the AD1580 needs only 50 uA minimum to hold its output, which is the property that puts it inside battery powered and loop powered instruments where every microamp is budgeted. The A grade output is 1.215 V to 1.235 V, temperature drift is 100 ppm per degree Celsius maximum, dynamic output impedance is 0.5 ohm, and the part is stable with any value of capacitive load. Turn on settling to 0.1 percent takes 5 microseconds.

Published values

ParameterValue
Output voltage, A grade1.215 V minimum to 1.235 V maximum
Temperature drift, A grade100 ppm per degree Celsius maximum
Minimum operating current50 uA
Dynamic output impedance0.5 ohm at 1 mA and 120 Hz
Output change with current2.5 mV typical, 6 mV maximum from 50 uA to 1 mA
Output noise0.4 uV to 1 uV rms from 10 Hz to 10 kHz
Turn on settling5 microseconds to 0.1 percent
Specified temperatureMinus 40 to plus 85 degrees Celsius
Operating temperatureMinus 55 to plus 125 degrees Celsius
BodiesSOT-23 and SC70

A shunt part needs a resistor, and the resistor sets the accuracy

Because the device regulates by sinking current, the series resistor has to supply both the reference current and whatever the load draws, over the full supply range and temperature range. Too large and the reference drops out at low supply; too small and it wastes current at high supply. The 50 uA minimum and the 6 mV maximum change from 50 uA to 1 mA give the usable window: the part is specified for load currents up to 1 mA and the resistor is chosen so the current never falls below 50 uA at the lowest supply voltage. If the load is a converter reference input that draws bursts, the resistor and the local capacitor together set how much the output moves during a burst.

Why 1.2 V rather than 2.5 V

A 1.2 V reference is close to the band gap voltage itself, which is the reason the part can work with so little headroom and so little current. The trade off is that a 1.2 V full scale is small for a converter input, so the reference is usually amplified or used as the low end of a bridge. In a 3 V system the 1.2 V reference sits comfortably below the rail, so the regulating resistor has 1.8 V across it and the arithmetic stays easy. In a 2.5 V system the headroom shrinks to 1.3 V and the resistor value has to be recalculated against the minimum supply, which is where most first builds go wrong.

Noise, impedance and the capacitor question

The output noise of 0.4 uV to 1 uV rms over the 10 Hz to 10 kHz band is low for a shunt device, and the 0.5 ohm dynamic impedance means an external capacitor is not needed for stability. That is convenient because a large capacitor at a reference output slows the turn on and stores charge that has to be dumped at power down. Where a capacitor is used, the value is chosen against the load transient rather than against stability, and the 5 microsecond turn on figure applies with no load capacitor, as the data sheet states.

Grades and the difference the B column makes

The B grade of the same device is specified at 1.224 V to 1.226 V, a 1 mV window against the 20 mV window of the A grade, with a drift figure of 50 ppm per degree against 100. The two parts share a body and a pinout, so a board can carry either, but a calibration step that assumed the A grade window will not remove the systematic offset of the B grade if the firmware expects a different nominal. Where the reference sets the full scale of a measurement, the grade is the accuracy of the instrument and should be chosen from the error budget rather than from availability. The ADI part second source page shows which grades are equivalent, the obsolete part cross reference hub covers the case where a grade has been dropped, and the lead time page shows what is on the shelf for both grades.