Braided Sleeving and Expandable Sleeves for Harness Protection
Product Specifications
Product Overview
A harness has three problems: it rubs, it bends and it has to pass through something. A conduit solves the first and the third and makes the second worse. A braided sleeve solves all three, because the braid is a fabric tube that bends to a tight radius, expands over a connector and then closes back onto the bundle. The two families on this page are the self-wrapping sleeve, which has a split and closes around the bundle, and the expandable sleeve, which is slid over the end.
The self-wrapping sleeve is Techflex Flexo F6. The braid is 10 mil PET, the split runs the length of the tube, and the 25 percent edge overlap at nominal diameter is what lets it cover an inline plug, a connector or a splice without a fastener. The nominal sizes run from 3.18 mm to 50.8 mm, the wall is 0.61 mm or 0.64 mm up to the 19.05 mm size and 0.97 mm on the larger parts, and the working range is -30 to 125 C with a melting point of 230 C. It is halogen free.
The self-wrapping part is the one to use on a harness that is already terminated. It opens along the split, is laid over the bundle and closes on itself, so a connector does not have to come off. That is why it is the standard repair and retrofit sleeve. The trade is that the split is a gap: on a bundle that changes diameter sharply the sleeve can gape, and the 25 percent overlap is what covers that gap at nominal size.
The expandable sleeve is Techflex Flexo PET. It is a closed tube braided from the same 10 mil PET yarn, and it expands up to 150 percent, which is the property that lets a 12.7 mm nominal sleeve open to 19.05 mm to pass a connector and then close back onto a 8 mm bundle. The sizes run from 1.59 mm nominal with a 1.19 to 2.38 mm range, through 6.35 mm nominal with a 3.18 to 11.11 mm range, to 50.8 mm nominal with a 38.1 to 88.9 mm range. It carries FMVSS 302 approval.
The expansion range, not the nominal size, is the figure to specify. A 6.35 mm sleeve that opens to 11.11 mm will not pass a 13 mm connector, and a 9.52 mm sleeve that opens to 12.7 mm will. On a branch, the sleeve is expanded at the junction and closes back on each leg, so the nominal size is chosen against the largest diameter that has to pass rather than against the bundle.
The practical points are cut, end and coverage. The braid is cut with a hot knife so the yarns fuse and the end does not unravel. The end is finished with heat shrink or a clamp, because an open braid end frays into the connector. And the coverage is chosen against the abrasion, not the size: a 0.61 mm wall on a small sleeve and a 0.97 mm wall on a large one are the same braid, and where the harness runs over a sharp edge the answer is a heavier sleeve or a grommet in the panel rather than a bigger diameter.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Braid material | 10 mil PET monofilament | Both families |
| Self-wrapping nominal size | 3.18 mm to 50.8 mm | Flexo F6 |
| Self-wrapping wall | 0.61 mm to 0.97 mm | Flexo F6 |
| Edge overlap | 25 percent at nominal diameter | Flexo F6 |
| Expandable nominal size | 1.59 mm to 50.8 mm | Flexo PET |
| Expansion range | 1.19 mm to 88.9 mm depending on size | Flexo PET |
| Maximum expansion | Up to 150 percent of nominal | Flexo PET |
| Temperature, self-wrapping | -30 to 125 C, melting 230 C | Flexo F6 |
| Halogen | Halogen free | Both families |
| Approval | FMVSS 302 | Flexo PET |
| Cut method | Hot knife | Both families |
| Colours | Black standard, other colours on request | Both families |
Included Models and Order Codes
The rows below are the self-wrapping sizes we quote most often. Nominal size and wall are given per part, because the split sleeve is chosen against the bundle it closes on rather than against a connector it has to pass.
| Part Number | Nominal Size | Wall | Type | Typical Use |
|---|---|---|---|---|
| F6N0.13 | 3.18 mm | 0.61 mm | Self-wrapping, split | Single wire and small branch |
| F6N0.25 | 6.35 mm | 0.64 mm | Self-wrapping, split | Three wire bundle |
| F6N0.38 | 9.52 mm | 0.64 mm | Self-wrapping, split | Sensor loom |
| F6N0.50 | 12.70 mm | 0.64 mm | Self-wrapping, split | Panel harness |
| F6N0.75 | 19.05 mm | 0.64 mm | Self-wrapping, split | Main bundle |
| F6N1.00 | 25.40 mm | 0.97 mm | Self-wrapping, split | Cabinet loom |
| F6N1.50 | 38.10 mm | 0.97 mm | Self-wrapping, split | Machine trunk |
| F6N2.00 | 50.80 mm | 0.97 mm | Self-wrapping, split | Large cable group |
Expandable Sleeving for Connector Pass Through
The expandable sleeve is slid over the end and opens to pass a connector. Nominal size and expansion range are given per part, and the range rather than the nominal size is what decides whether the connector goes through.
| Part Number | Nominal Size | Expansion Min | Expansion Max | Typical Use |
|---|---|---|---|---|
| PTN0.06 | 1.59 mm | 1.19 mm | 2.38 mm | Single fine wire |
| PTN0.13 | 3.18 mm | 2.38 mm | 6.35 mm | Small connector |
| PTN0.25 | 6.35 mm | 3.18 mm | 11.11 mm | D sub and circular connector |
| PTN0.38 | 9.52 mm | 4.76 mm | 12.70 mm | Sensor cable |
| PTN0.50 | 12.70 mm | 6.35 mm | 19.05 mm | Panel harness |
| PTN0.75 | 19.05 mm | 12.70 mm | 31.75 mm | Main bundle |
| PTN1.00 | 25.40 mm | 15.88 mm | 41.28 mm | Cabinet trunk |
| PTN1.50 | 38.10 mm | 25.40 mm | 53.98 mm | Large trunk |
| PTN2.00 | 50.80 mm | 38.10 mm | 88.90 mm | Multi cable group |
Key Features
Expansion range per size – The expandable parts are listed with a minimum and maximum diameter, because the connector and the bundle are two different figures.
Split sleeve for retrofits – The self-wrapping part opens along its length, so a terminated harness can be sleeved without removing a connector.
25 percent edge overlap – The overlap covers the gap at nominal size, which is what keeps an inline plug or a splice closed.
Wall stated per part – 0.61 mm, 0.64 mm and 0.97 mm walls are listed, so a larger sleeve is not assumed to give more abrasion protection.
Halogen free PET braid – Both families are halogen free, which is what a cabinet or a rail build asks for.
Hot knife cut – The braid is cut with a hot knife so the yarns fuse, because a frayed end works its way into a connector.
Applications
These parts are used on harnesses that rub against a frame, bend through a tight radius or have to pass a connector through a panel.
Machine frame looms – A 12.7 mm self-wrapping sleeve closes over a 10 mm bundle that already has its connectors, and the 25 percent overlap covers the branch.
Panel pass through – A 19.05 mm expandable sleeve opens from 12.7 mm to 31.75 mm to pass a circular connector, then closes back onto the cable.
Retrofit and repair – A 9.52 mm split sleeve is laid over a damaged section without cutting the wire, and the ends are finished with heat shrink.
A sleeve is the last thing fitted to a loom, so the expansion range is checked against the SUPERB PCB connector stack before the harness length is fixed. On the SUPERB PCBA route the sleeving goes on after the connectors are soldered, because a sleeve fitted before the last connector is a sleeve that has to come off again.
Sourcing and Cross-Reference
A sleeve is bought by expansion and by abrasion. The expansion decides whether it goes over the connector, and the wall decides how long it lasts against an edge. When a sleeve is replaced on a harness that is already built, the bundle diameter, the largest connector and the edge it rubs against are the three figures to send, because a 6.35 mm nominal part and a 9.52 mm nominal part can both close on the same bundle.
The second point is the fence at each end. A braided sleeve that is left open frays into the connector, and a sleeve that is clamped too tight crushes the bundle. Heat shrink over the end is the usual answer, and a cable tie inside the sleeve is the answer where the end has to stay flexible. The cut itself is made with a hot knife so the yarns fuse, which is the difference between an end that stays put and one that unravels on the first pull.
The third point is coverage. A split sleeve is fast to fit and covers a branch, but it is a gap as well as a cover, and on a bundle that changes diameter the split opens. An expandable sleeve is closed and covers better, but it has to be slid on before the connector is fitted. Most looms use both, the expandable part on the trunk and the split part on the branches. We quote the sleeve with its expansion range, because that is the figure the harness drawing is checked against.
SUPERB Assembly fits the first length over a connector, opens it to the maximum and lets it close, because a sleeve that only just covers the bundle is a sleeve that gapes at every branch.
Q: Can you supply expandable sleeving that opens from 12.7 mm to 32 mm to pass a circular connector, plus split sleeving for the branches, in one order?
A: Send the bundle diameter, the largest connector it has to pass and the abrasion it has to take. The SUPERB Tech desk quotes the sleeve by its expansion range, because a 6.35 mm sleeve that opens to 11 mm is not the same part as a 6.35 mm sleeve that opens to 16 mm.
Why Buy Braided Sleeving Through SUPERB
- Expansion range on the quote: Both the nominal size and the range are given, because the connector and not the bundle sets the size.
- Split and closed types: Self-wrapping and expandable parts are on one page, so a retrofit and a new loom are not forced onto the same sleeve.
- Wall stated per part: The wall is quoted per part, so a larger sleeve is not ordered expecting more abrasion resistance.
- Halogen free material: The PET braid is halogen free, which is what a cabinet or a rail build asks for at drawing review.
- Ends finished at assembly: The first length is fitted with its ends closed, because an open braid end frays into the connector it was meant to protect.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Heat Shrink Tubing and Sleeves for Harness Protection, Cable Clamps and Harness Ties for Internal Wiring, Cable Markers and Wire Labels for Harness Identification, Nylon Grommets and Hole Plugs for Panel Openings, Wire Ferrules and Crimp Sleeves for Terminal Blocks, BOM Shortage Recovery.