Contact Us

TMP100NA/3K

Brand: Texas Instruments
Texas Instruments TMP100NA/3K is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP100NA/3K — Power Management & Signal Chain | Superb Automation

TMP100NA/3K

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP100NA/3K from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP100NA/3K: a digital temperature sensor in a six pin SOT-23

The TMP100NA/3K is a digital temperature sensor with an I2C and SMBus interface in a six pin SOT-23 body. It converts on chip with a 12 bit converter and reports temperature as a digital word with a resolution of 0.0625 C, which removes the calibration work that an NTC or a thermocouple path needs.

Accuracy is plus or minus 1 C typical and plus or minus 2 C maximum across minus 55 to 125 C, without calibration. The supply range is 2.7 V to 5.5 V, so it can sit on a 3.3 V rail or a 5 V rail, and the quiescent current is 45 microamps with a 0.1 microamp standby.

The six pin body carries the bus, the supply, an address pin and, on the TMP101 version of the same die, an alert output. This order code uses the third pin for address selection, which allows several sensors on one bus without an external multiplexer.

Key data for the TMP100NA/3K

FunctionDigital temperature sensor with a two wire interface
InterfaceI2C and SMBus compatible
Resolution12 bit, 0.0625 C per step
AccuracyPlus or minus 1 C typical, plus or minus 2 C maximum, no calibration
RangeMinus 55 to 125 C
Supply2.7 V to 5.5 V
Current45 microamps active, 0.1 microamps standby
AddressingAddress pin selects the bus address, several devices on one bus
AlertAvailable on the TMP101 member of the family
PackageSOT-23, 6 pins, 2.90 mm by 1.60 mm
Temperature rangeMinus 55 to 125 C operation
OrderingTMP100NA/3K, 3000 pieces on a large tape and reel

What replaces a thermistor, and what does not

A thermistor is cheap, small and needs a divider, an analog input and a table. A digital sensor costs more per point and needs a bus, but it removes the table, the tolerance stack of the divider resistors and the calibration step at the end of the line. For a product with one or two measurement points, the thermistor usually wins. For a product with six points on one board, the bus sensor is usually cheaper once the analog channels and the calibration time are counted.

The trade does not disappear, it moves. A digital sensor measures the temperature of its own package, which is the temperature of the board under it, not the temperature of the air or of the object being controlled. A thermistor on a flying lead can be placed where the heat is. A board mounted sensor needs the thermal path built, with copper connecting it to the hot component and isolation from anything that is cool.

Response time follows the same logic. A SOT-23 on a copper plane has a thermal time constant of tens of seconds. A product that has to catch a fast rise needs the sensor close to the source, or a different package with less copper attached.

Reading the bus reliably on a noisy board

The interface is a two wire bus with pull up resistors, and the value of those resistors decides both the rise time and the current drawn when a device holds the line low. On a board with a switching supply, a 2.2 kilo ohm pull up gives a fast edge and a clean read, at the cost of a milliamp or two when the line is low.

Address conflicts are the common failure. Several sensors in one package family share a base address, and the address pin moves the number by a few steps. A bus with two devices set to the same address will appear to work until one of them answers at the wrong moment, and then a temperature reading comes from the wrong point.

The 12 bit result also has to be assembled correctly. It arrives as two bytes, and a host that reads them in separate transactions can pick up a value that was updated between the two. Reading both bytes in one transaction, or using the alert function to latch a conversion, is the fix.

Where it fits in a build

Medical instruments, bench equipment, industrial controllers and any board where a temperature has to be logged rather than controlled. The SOT-23 body is small enough to place next to the component it monitors, and the 2.7 V supply range covers both 3.3 V and 5 V logic.

In a medical build the sensor is part of a record, so the part number and the date code matter as much as the accuracy. The medical device components page sets out how we hold traceability on parts like this, and the incoming inspection plan page covers the checks at the receiving dock.

The sourcing side of this part is covered on the date code management. For a small sensor bought in reels of three thousand, that page covers how reel age is tracked and what we will not ship into a new build.

Questions we get on this code

Can several sensors share one bus? Yes, within the number of addresses the pin arrangement allows. Confirm the address map before the board is routed, because the pin that sets the address cannot be changed afterwards.

Does it need a pull up on the alert pin? This order code has no alert pin. On the TMP101 version the alert is an open drain output and needs a pull up, like the data line.

How accurate is it at the extremes? The maximum error figure covers the whole range, and it is larger than the typical figure on purpose. A product that needs a tight guarantee over temperature should not budget on the typical number.

Is the part a drop in replacement for other sensors in the same footprint? The register map is common in the family, but the address pin and the alert function differ between members. Check the pin function list rather than the package outline.