On a 3.2 mm board our standard line stops at 0.32 mm, which is a 10:1 ratio of depth to diameter. The high-layer line reaches 0.15 mm, and 0.15 mm through 3.2 mm is 21:1. Below 0.15 mm there is no mechanical drill at all. So on a thick board, how small a hole can be is really a question about which line builds the board, and the answer moves with thickness rather than with the drawing alone.
The ratio is not a house convention. It is a limit on how fresh plating solution reaches the middle of the hole. At 10:1 the solution exchanges freely and the barrel plates close to the surface figure. At 20:1 the exchange at mid depth depends on agitation, on the hole diameter and on how the current is applied, and the barrel reads thin exactly where a thermal cycle will pull it apart. That is why the ratio sits next to the drill range in the capability list.
The drill is not the hole
This is the part that changes the answer. Plating grows on the barrel wall, so the finished hole is smaller than the drill by twice the plating thickness. With our published barrel copper of at least 20 micrometres, a 0.20 mm drill finishes at about 0.16 mm.
Now put that on a 3.2 mm board. The drilling ratio is 16:1 and the finished ratio is 20:1, both from the same tool. A customer who checks only the drill number and a fabricator who quotes on the finished hole can disagree by four ratio points on the same via, which is enough to move a job from the standard line to the high-layer line without anyone intending it.
The same effect decides whether the part fits. A press-fit pin is specified against the finished hole with a plus or minus 0.05 mm window, and our published plated hole tolerance is plus or minus 0.075 mm, so a small plated hole is quoted with its tooling and its drill size rather than as one nominal figure. On holes below 0.30 mm we agree the working window with the customer before the panel starts, because the tolerance that is comfortable on a 0.8 mm hole is half the diameter on a 0.20 mm hole.
What a small hole does to the pad
A hole is not usable without an annular ring, and the ring plus the registration error sets the pad. Our published ring is 3.5 mil (0.089 mm) on a via at 1 oz copper and 4.5 mil at 2 oz, with component holes at 8.0 and 10.0 mil. Layer-to-layer registration is plus or minus 0.025 to 0.06 mm, and drill position tolerance is plus or minus 0.075 mm.
Take a 0.15 mm hole and put a 0.089 mm ring on it with 0.05 mm of registration error: the pad comes out at 0.15 plus 0.178 plus 0.10, about 0.43 mm. At 0.5 mm pitch that leaves 0.07 mm between pads, which is a workable gap on an outer layer and a hard one on an inner layer under mask. That arithmetic, not the drill size, is what stops most thick board layouts from shrinking further. It also explains why fine geometry on a thick board moves to laser vias and sequential lamination instead of to smaller mechanical drills.
Three ways the request goes wrong
Sizing the hole from the pin and ignoring thickness. A 0.20 mm finished hole in a 1.6 mm board is comfortable. The same 0.20 mm in a 3.2 mm board is 16:1 on the drill and 20:1 finished, it belongs on the high-layer line, and both the price and the lead time change. Thickness belongs in the hole table, not only on the mechanical drawing.
Counting a laser via as an escape for a through hole. Laser drilling reaches 0.075 to 0.15 mm and it only goes into the adjacent layer. It cannot pass through 3.2 mm of laminate. What actually solves a dense thick board is sequential lamination with buried and blind vias, up to seven press cycles on our side, which is a stack decision and not a drilling one. The limits on the laser side are in which microvia aspect ratio is reliable.
Quoting a hole without its ring and its finish. A 0.15 mm drill with 20 micrometres of wall finishes at about 0.11 mm, and the ring on top of that takes the pad to roughly 0.40 mm before registration is counted. A quote that prices the drill and forgets the ring comes back with a pad that does not fit the connector footprint.
Forgetting that plating closes the hole on a thick board. On a 3.2 mm board with 25 micrometres of wall the same 0.15 mm drill finishes near 0.10 mm, which is over 30:1 on the finished hole and under the pin diameter for most press-fit parts. If the drawing needs a 0.15 mm finished hole, the drill has to be larger than 0.15 mm, and the ratio has to be checked on the finished figure.
What SUPERB PCB holds on holes
Published: mechanical drilling 0.15 to 6.35 mm; laser drilling 0.075 to 0.15 mm with a 0.05 mm minimum; plated slots from 0.50 mm and non-plated slots from 0.80 mm; aspect ratio 10:1 on the FR-4 standard line and up to 25:1 on the high-layer line; barrel copper at least 20 micrometres; hole position plus or minus 0.075 mm, plated hole plus or minus 0.075 mm and press-fit plus or minus 0.05 mm, non-plated plus or minus 0.05 mm, slots plus or minus 0.10 mm; annular ring 3.5 mil on vias at 1 oz and 4.5 mil at 2 oz, 8.0 and 10.0 mil on component holes; layer-to-layer registration plus or minus 0.025 to 0.06 mm; back-drill stub 0.25 mm or less with depth control of plus or minus 0.05 mm; 68 layers maximum. The list is on the capability page, and the barrel thickness that goes with it is covered in copper plating in a plated hole.
The honest boundary: 25:1 is a line capability that depends on hole size, plating and stack, not a promise that any 25:1 hole will plate to the same figure as a 10:1 hole. Below 0.15 mm we do not drill mechanically at all, and a layout that needs a 0.10 mm through hole needs a different stack rather than a smaller tool.
SUPERB Tech runs the thick, high layer work on the multilayer PCB line, where the drill schedule, the press cycles and the registration budget are agreed before the first panel. Where a layout also needs back-drilling to keep a stub short, the cost side of that decision is in when back-drilling is worth the cost.
What to send with the drill table
Finished board thickness, the finished diameter of every critical hole rather than the drill size, the pin or press-fit specification, the annular ring the part needs, the connector pitch, whether each hole is plated or non-plated, whether back-drilling is required, and the copper weight on the layers the holes pass through. Eight lines, and the drill schedule follows without a second round of questions.