Contact Us
  • Home
  • BLOG
  • When Is Back-Drilling Worth It on a High-Speed Backplane?

When Is Back-Drilling Worth It on a High-Speed Backplane?

Back-drilling is worth the cost when the via stub left behind by a through hole is long enough to resonate inside the band your link actually uses. Do the arithmetic before you quote it: the stub resonates at f = c divided by four times the stub length times the square root of the dielectric constant, and if that number sits within about twice your Nyquist frequency, the stub is already costing you margin. If it sits far above the band, back-drilling is money spent on a problem you do not have.

The mechanism, and where the numbers land

A plated through hole that runs from the top layer to the bottom layer of a 3.2 mm backplane carries a copper barrel the full thickness of the board. When a signal enters on layer 3 and leaves on layer 5, the part of the barrel below layer 5 is still connected, still plated, and still open at the far end. Electrically it is a transmission line with a short at one end, which behaves as a quarter wave resonator.

Take a 3.2 mm board with a Dk of 4.2 and a signal pair that enters on layer 3. The unused stub is roughly 2.4 mm. With a Dk of 4.2 the square root is 2.05, so the quarter wave frequency is 3e8 divided by 4 times 0.0024 times 2.05, which is about 15.2 GHz. A 25 Gb/s NRZ link has a Nyquist frequency of 12.5 GHz, and a 56 Gb/s PAM4 link sits at 14 GHz. In both cases the first stub resonance is inside or immediately above the working band, and the insertion loss starts to roll off and the return loss to peak well before the null itself arrives.

Shorten the stub to 0.5 mm and the same formula puts resonance at about 73 GHz, which is far outside any of those links. That is the whole trade: the drill pass buys you the removal of a resonator that was inside the band.

Stub lenh>First resonanceTypical fit
2.4 mmAbout 15.2 GHzMarginal at 25 Gb/s NRZ, fails at 56 Gb/s PAM4
1.0 mmAbout 36.6 GHzWorkable to 25 Gb/s, tight at 56 Gb/s
0.25 mmAbout 146 GHzComfortable at 56 Gb/s PAM4 and above

What it costs is one extra drill pass per board, a second drilling program, and a depth control that has to hold about plus or minus 0.05 mm. In practice a back-drilled backplane carries roughly 10 to 20 percent on the bare board price and two to four days on lead time, because the panel goes through the drill room twice and the second pass cannot be run at the same feed rate as the first.

What goes wrong in the specification

Back-drilling every via. Only vias on high-speed nets with a long unused stub need it. Counter-drilling a power via or a low speed signal via adds cost, adds a chance of damaging the barrel, and changes nothing electrically. The list should come from the stack-up and the net class, not from a general instruction to back-drill the board.

No stub allowance on the target layer. The drill has to stop short of the target inner layer pad, and the distance it stops short is the stub you keep. With depth control at plus or minus 0.05 mm and a drill tip that is not flat, a stack-up that leaves only 0.1 mm of allowance will break through on some panels. Build the layer assignment so the target layer sits at least 0.2 mm below the intended drill depth, and state the maximum acceptable stub on the fabrication drawing instead of leaving it to the shop.

Shortening the barrel under a press-fit connector. A back-drilled via has less copper barrel than the drawing assumed. If a press-fit pin is specified into that hole, the compliant section may end up with too little barrel to grip, or the pin may protrude into the back-drilled void. Press-fit holes and back-drilled holes have to be reconciled in the hole table, with the pin length, the board thickness and the remaining barrel called out together.

No stub verification on the finished panel. Stub length is not visible after lamination. It is proven either by cross section on a coupon from the same panel, or by a TDR measurement on a daisy chain structure built into the coupon. A back-drilled board shipped without one of those two records is a board whose stub length is a claim rather than a measurement.

How SUPERB supports a back-drilled backplane

SUPERB PCB runs back-drilling with a residual stub of 0.25 mm or less and depth control of plus or minus 0.05 mm, on high layer count work up to 68 layers, with mechanical drills from 0.15 mm and laser vias from 0.075 mm where the stack-up needs them. Layer to layer registration is held at 0.025 to 0.06 mm, impedance is controlled to plus or minus 5 percent with plus or minus 2 percent on critical nets, and each panel carries a TDR impedance coupon so the stub and the impedance are measured rather than assumed. Up to seven lamination cycles are available for the mixed material builds that backplanes often need.

The same flow covers the assembly side of the program: press-fit connectors, 0.45 mm pitch BGA and the high layer count reflow that goes with them, handled through our high-speed digital PCB capability and then assembled as a switch backplane PCBA or a router backplane board under one purchase order through SUPERB Assembly.

If you are deciding whether a backplane needs the second drill pass, send the stack-up and the link rate. The reply states the stub length your current layer assignment leaves, the resonance that produces, and whether the drill pass is worth quoting at all.

Need a quote or a quality evidence review on your files? pcba@superb-tech.com · WhatsApp +86 133 9608 1443