UCC27525DSDR
Product Specifications
UCC27525DSDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27525DSDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27525DSDR: one inverting and one non-inverting channel in a 3 mm by 3 mm body
The UCC27525DSDR is the mixed polarity member of the UCC2752x family. Channel A inverts and channel B does not, which is the arrangement a half bridge needs when a single logic signal has to turn one switch on while the other turns off, without an external inverter. Drive current is 5 A source and 5 A sink on each channel, the supply range is 4.5 V to 18 V, propagation delay is 13 ns typical and the rise and fall times are 7 ns and 6 ns, both faster than the UCC27524 because this die is the newer of the two families.
The package in the catalogue code is DSD, the 3 mm by 3 mm WSON with an exposed pad, packed 3000 pieces on a large reel. That body is the one to pick when the driver sits within a few millimetres of the switches and the thermal path has to run into the copper plane rather than into the air. The enable pins work the same way as on the rest of the family, pulled up internally, and the outputs stay low while the supply is below the lockout and while an input floats. The junction rating on this member is minus 40 C to 140 C, which is 10 C lower than the UCC27524 datasheet headline and is the number to use for a sealed enclosure calculation.
Key electrical data for the UCC27525DSDR
| Supply | 4.5 V to 18 V, outputs held low during undervoltage lockout |
| Polarity | Channel A inverting, channel B non-inverting, independent enable on each channel |
| Drive | 5 A peak source and sink per channel, rail to rail, outputs may be paralleled |
| Timing | 13 ns typical propagation delay, 7 ns rise, 6 ns fall, 1 ns typical channel matching |
| Inputs | TTL and CMOS thresholds fixed against the supply, wide hysteresis for noise immunity |
| Temperature | Junction range minus 40 C to 140 C on the DSD body |
Package, marking and reel data
| Body | DSD, WSON 8 pin with exposed pad, 3.00 mm by 3.00 mm |
| Reel | 3000 pieces on a 330 mm reel, large tape and reel carrier |
| Finish | NIPDAU, moisture level 2 at 260 C with a one year floor life on the .A and .B rows |
| Marking | 27525 on the top of the body |
The addendum prints two different bodies under one code
There is a detail in the vendor addendum that matters on a purchase order. The row printed as UCC27525DSDR carries the package column SOIC (D) with 8 pins and moisture level 1, while the .A and .B rows of the same string carry SON (DSD) with moisture level 2 and a one year floor life. The catalogue code is the DSD body, which is what the datasheet describes for the 3 mm by 3 mm part, so the plain row is a printing artifact rather than a second body. The practical consequence is that the moisture level and the floor life have to come from the label on the reel in hand, not from the row that happens to be first in the list. Our incoming inspection plan page sets out how we check that before a lot reaches a line.
For a synchronous rectifier pair the mixed polarity is what makes one control signal enough. Feed the same signal into both inputs, and channel A pulls its gate low while channel B pulls its gate high, with 1 ns of matching between them. Add the dead time in the controller rather than in the driver, because the driver has no programmable delay. Where both switches need the same polarity, the UCC27523 or the UCC27524 is the right code and the pinout stays the same.
Buyer questions on the UCC27525DSDR
Can the inverting channel be used as a non-inverting one? Only by inverting the signal before it reaches the pin. The polarity is fixed by the die, so a board that needs two non-inverting channels should take the UCC27523 or the UCC27524 instead.
Does the exposed pad need vias? It does. The pad is the thermal path, and a driver switching a large gate at high frequency dissipates most of its heat through it, so several vias into a copper plane are part of the connection rather than an option.
How does the 140 C rating compare with the 150 C on other members? The DSD member is published at 140 C junction, so a build that relies on 150 C has to move to the body that carries the higher figure. Both are active and both are 5 A parts, so the choice is thermal, not electrical.
Availability and cross reference
The 3000 piece reel is the published packing, and the 250 piece small reel exists on the sibling body for prototype runs. Because the three members of the family share a pinout, a build that starts with a mixed polarity driver and later needs two non-inverting channels can change the code without touching the board, as long as the enable pins are treated the same way. Our power management cross reference page lists the family and the second sources we hold against forecast.