Contact Us

UCC27516DRSR

Brand: Texas Instruments
Texas Instruments UCC27516DRSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27516DRSR — Power Management & Signal Chain | Superb Automation

UCC27516DRSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27516DRSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27516DRSR: 4 A in and 4 A out from a 4.5 V rail, in a six pin SON

The UCC27516DRSR is a single channel low side gate driver with symmetric 4 A peak source and sink, 13 ns typical propagation delay and 9 ns rise and 7 ns fall times. It runs from 4.5 V to 18 V, uses a dual input arrangement that lets the board choose inverting or non-inverting action by which pin is driven, and holds the output low during the supply UVLO window so a controller that comes up after the driver does not see a spurious gate pulse during the ramp, which is the behaviour a hot swap controller needs when it enables a 12 V rail into a pre-charged load, and the 13 ns propagation delay is short enough that the gate follows the controller without a measurable skew.

Its commercial position is as a replacement for a discrete NPN and PNP totem pole. A two transistor buffer with base resistors takes six parts, has a crossover region where both devices conduct, and needs a separate pull-down resistor. The UCC27516 does the same job in a 2 mm by 2 mm body with 4 A of symmetric drive, and the input thresholds are independent of the supply, so a 3.3 V controller can drive a 12 V gate without a level shifter.

Key electrical data for the UCC27516DRSR

Drive4 A peak source and 4 A peak sink, symmetric
Supplies4.5 V to 18 V single supply, outputs held low during UVLO
Timing13 ns typical propagation delay, 9 ns rise and 7 ns fall
InputDual input allows inverting or non-inverting action, TTL and CMOS thresholds independent of supply
LogicHysteretic thresholds for noise immunity, shoot-through current minimised internally
GradeJunction -40 C to 140 C, SON and SOT-23 body options

Package, marking and reel data

BodyDRS, 6 pin SON, 2.0 mm by 2.0 mm
Reel3000 pieces on a large reel, 250 pieces on the small reel code DRST
FinishNIPDAU, level 2 at 260 C, one year floor life
AlternateThe UCC27517 in the 5 pin SOT-23 is the same drive in a different body, 3000 pieces per reel

What the dual input arrangement buys

With two input pins, one inverting and one non-inverting, the same part can buffer a high side signal or invert a fault signal without a logic gate. The unused input is tied to a rail rather than left floating, because the internal logic resolves the two pins against each other and a floating pin picks up the switch node. That detail is in the pin description rather than the feature list, and a board that leaves the second input open will show random pulses at the gate whenever the load current changes.

The 4.5 V floor is the other constraint. A 5 V rail drives the part at its minimum recommended supply, so a rail that sags during a load step can push the input below the UVLO and drop the gate at the moment the MOSFET is carrying current. A 12 V rail is the safer arrangement, and the 18 V ceiling keeps it clear of the gate oxide limit of most silicon MOSFETs, while a 15 V rail leaves the least headroom for overshoot on the gate node and is the usual choice for an IGBT. power MOSFETs. Our power management cross reference page lists the low side drivers we hold for this class.

Buyer questions on the UCC27516DRSR

Which input do I drive for a non-inverting buffer? Drive the non-inverting input and tie the inverting input low, or drive the inverting input and tie the other high for an inverted result. Neither input can be left floating.

Is the SOT-23 version identical? The UCC27517 in SOT-23 carries the same 4 A drive in a five pin body with a different pinout, so it is a circuit level substitution rather than a board one.

Does the driver need a gate resistor? A small series resistor is still normal, because 4 A into a gate loop with a few nanohenries rings. The resistor damps the ring and sets the turn-on edge without giving up much of the drive current.

Availability and cross reference

This code ships 3000 pieces per reel and the small reel code carries 250. Moisture level 2 at 260 C means a year of floor life, which is long enough that a partial reel can go back on the shelf without a bake. Because the SON and the SOT-23 bodies are not footprint compatible, we quote by body and list both on the quotation when a customer is moving a buffer from a discrete arrangement to an integrated driver. Our BOM consolidation page describes how a board with four discrete buffers collapses into two of these parts.