Contact Us

UCC27200DR

Brand: Texas Instruments
Texas Instruments UCC27200DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27200DR — Power Management & Signal Chain | Superb Automation

UCC27200DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27200DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27200DR: a 120 V half bridge driver with the bootstrap diode already inside

The UCC27200DR drives two N channel MOSFETs in a half bridge configuration with a 120 V bootstrap diode built into the package. That diode is 0.65 V forward drop and 0.65 ohm series resistance, so the bootstrap capacitor charges from the 12 V rail without an external diode and without the board area that diode needs. The driver sources and sinks 3 A, quotes 22 ns propagation delay with 1 ns of delay matching between the high side and the low side, and switches an 8 ns rise and 7 ns fall into a 1000 picofarad load.

Two input versions exist. The UCC27200 has CMOS thresholds with high noise immunity, the UCC27201 has TTL thresholds, and the two are otherwise the same silicon. That choice matters when the controller rail is 3.3 V and the driver runs from 12 V: a TTL threshold part accepts the 3.3 V logic directly, while a CMOS threshold part needs the input to reach a fraction of its own supply and may not switch reliably. The part is specified from minus 40 C to 150 C and handles minus 5 V on the switch node, which is what a bridge sees during commutation ringing.

Key electrical data for the UCC27200DR

TopologyHalf bridge driver for two N channel MOSFETs, independent high side and low side inputs
Voltages120 V maximum bootstrap, 20 V maximum VDD, minus 5 V on the HS pin
Drive3 A sink and 3 A source, 8 ns rise and 7 ns fall with a 1000 pF load
Timing22 ns propagation delay, 1 ns delay matching between the two channels
BootstrapOn chip diode, 0.65 V forward drop and 0.65 ohm series resistance
GradeSpecified -40 C to 150 C, UVLO on both the high side and the low side driver

Package, marking and reel data

BodyDDA, 8 pin SO PowerPAD, exposed pad for thermal conduction
Reel2500 pieces on a large reel for this code, 3000 on the DRC body option
FinishNIPDAU, level 1 at 260 C with unlimited floor life
NoteThe plain row is specified to 150 C, the .A row of the same code to 140 C in the addendum

Where a 120 V half bridge driver still wins

Telecom and merchant power supplies, solar micro inverters, online UPS and battery test equipment all run a half bridge or a synchronous buck at a bus voltage between 48 V and 100 V, and this driver covers that window with one part and no external bootstrap diode. The 1 ns delay matching is what keeps the two switches from overlapping: at 100 kHz a 1 ns mismatch is 0.01 percent of the period, so the dead time can be set close to the minimum the MOSFET needs rather than padded for driver spread.

The bootstrap capacitor is the part that decides whether the high side stays alive at high duty. It has to hold the gate charge of the high side MOSFET plus the quiescent current of the high side driver through the on time, and with a 0.65 V drop in the internal diode the available rail is 11.35 V on a 12 V supply. A 100 nanofarad capacitor is enough for a 30 nanocoulomb gate charge at 100 kHz; a larger device or a lower frequency needs proportionally more. Our power management cross reference page lists the drivers and the MOSFETs we pair for this bus class.

Buyer questions on the UCC27200DR

What is the difference between the UCC27200 and the UCC27201? Only the input thresholds. The 27200 is CMOS with high noise immunity, the 27201 is TTL compatible. The drive current, the timing and the bootstrap diode are the same.

Can the driver be used in a full bridge? Yes, two parts make a full bridge, with each high side driven from its own bootstrap capacitor. The vendor lists full bridge, two switch forward and active clamp forward among the supported topologies.

Why is the HS pin rated to minus 5 V? Because the switch node undershoots during commutation. The rating tells you how far the node can ring below ground without damaging the driver, and a board with a long loop will exceed it.

Availability and cross reference

This code ships 2500 pieces per reel at level 1 with unlimited floor life, which makes it one of the easier parts in this band to hold in open stock. The exposed pad on the DDA body has to be soldered to a copper area for thermal conduction, and a reflow profile that leaves it unsoldered will still pass a functional test and fail in the field. Our incoming inspection plan covers the solderability check we run on this body.